1 /******************************************************************************
3 * This file is provided under a dual BSD/GPLv2 license. When using or
4 * redistributing this file, you may do so under either license.
8 * Copyright(c) 2005 - 2014 Intel Corporation. All rights reserved.
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of version 2 of the GNU General Public License as
12 * published by the Free Software Foundation.
14 * This program is distributed in the hope that it will be useful, but
15 * WITHOUT ANY WARRANTY; without even the implied warranty of
16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
17 * General Public License for more details.
19 * You should have received a copy of the GNU General Public License
20 * along with this program; if not, write to the Free Software
21 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110,
24 * The full GNU General Public License is included in this distribution
25 * in the file called COPYING.
27 * Contact Information:
28 * Intel Linux Wireless <linuxwifi@intel.com>
29 * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
33 * Copyright(c) 2005 - 2014 Intel Corporation. All rights reserved.
34 * All rights reserved.
36 * Redistribution and use in source and binary forms, with or without
37 * modification, are permitted provided that the following conditions
40 * * Redistributions of source code must retain the above copyright
41 * notice, this list of conditions and the following disclaimer.
42 * * Redistributions in binary form must reproduce the above copyright
43 * notice, this list of conditions and the following disclaimer in
44 * the documentation and/or other materials provided with the
46 * * Neither the name Intel Corporation nor the names of its
47 * contributors may be used to endorse or promote products derived
48 * from this software without specific prior written permission.
50 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
51 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
52 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
53 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
54 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
55 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
56 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
57 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
58 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
59 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
60 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
62 *****************************************************************************/
64 * Please use this file (commands.h) only for uCode API definitions.
65 * Please use iwl-xxxx-hw.h for hardware-related definitions.
66 * Please use dev.h for driver implementation definitions.
69 #ifndef __iwl_commands_h__
70 #define __iwl_commands_h__
72 #include <linux/ieee80211.h>
73 #include <linux/types.h>
79 REPLY_ECHO = 0x3, /* test command */
81 /* RXON and QOS commands */
83 REPLY_RXON_ASSOC = 0x11,
84 REPLY_QOS_PARAM = 0x13,
85 REPLY_RXON_TIMING = 0x14,
87 /* Multi-Station support */
89 REPLY_REMOVE_STA = 0x19,
90 REPLY_REMOVE_ALL_STA = 0x1a, /* not used */
91 REPLY_TXFIFO_FLUSH = 0x1e,
98 REPLY_LEDS_CMD = 0x48,
99 REPLY_TX_LINK_QUALITY_CMD = 0x4e,
101 /* WiMAX coexistence */
102 COEX_PRIORITY_TABLE_CMD = 0x5a,
103 COEX_MEDIUM_NOTIFICATION = 0x5b,
104 COEX_EVENT_CMD = 0x5c,
107 TEMPERATURE_NOTIFICATION = 0x62,
108 CALIBRATION_CFG_CMD = 0x65,
109 CALIBRATION_RES_NOTIFICATION = 0x66,
110 CALIBRATION_COMPLETE_NOTIFICATION = 0x67,
112 /* 802.11h related */
113 REPLY_QUIET_CMD = 0x71, /* not used */
114 REPLY_CHANNEL_SWITCH = 0x72,
115 CHANNEL_SWITCH_NOTIFICATION = 0x73,
116 REPLY_SPECTRUM_MEASUREMENT_CMD = 0x74,
117 SPECTRUM_MEASURE_NOTIFICATION = 0x75,
119 /* Power Management */
120 POWER_TABLE_CMD = 0x77,
121 PM_SLEEP_NOTIFICATION = 0x7A,
122 PM_DEBUG_STATISTIC_NOTIFIC = 0x7B,
124 /* Scan commands and notifications */
125 REPLY_SCAN_CMD = 0x80,
126 REPLY_SCAN_ABORT_CMD = 0x81,
127 SCAN_START_NOTIFICATION = 0x82,
128 SCAN_RESULTS_NOTIFICATION = 0x83,
129 SCAN_COMPLETE_NOTIFICATION = 0x84,
131 /* IBSS/AP commands */
132 BEACON_NOTIFICATION = 0x90,
133 REPLY_TX_BEACON = 0x91,
134 WHO_IS_AWAKE_NOTIFICATION = 0x94, /* not used */
136 /* Miscellaneous commands */
137 REPLY_TX_POWER_DBM_CMD = 0x95,
138 QUIET_NOTIFICATION = 0x96, /* not used */
139 REPLY_TX_PWR_TABLE_CMD = 0x97,
140 REPLY_TX_POWER_DBM_CMD_V1 = 0x98, /* old version of API */
141 TX_ANT_CONFIGURATION_CMD = 0x98,
142 MEASURE_ABORT_NOTIFICATION = 0x99, /* not used */
144 /* Bluetooth device coexistence config command */
145 REPLY_BT_CONFIG = 0x9b,
148 REPLY_STATISTICS_CMD = 0x9c,
149 STATISTICS_NOTIFICATION = 0x9d,
151 /* RF-KILL commands and notifications */
152 REPLY_CARD_STATE_CMD = 0xa0,
153 CARD_STATE_NOTIFICATION = 0xa1,
155 /* Missed beacons notification */
156 MISSED_BEACONS_NOTIFICATION = 0xa2,
158 REPLY_CT_KILL_CONFIG_CMD = 0xa4,
159 SENSITIVITY_CMD = 0xa8,
160 REPLY_PHY_CALIBRATION_CMD = 0xb0,
161 REPLY_RX_PHY_CMD = 0xc0,
162 REPLY_RX_MPDU_CMD = 0xc1,
164 REPLY_COMPRESSED_BA = 0xc5,
167 REPLY_BT_COEX_PRIO_TABLE = 0xcc,
168 REPLY_BT_COEX_PROT_ENV = 0xcd,
169 REPLY_BT_COEX_PROFILE_NOTIF = 0xce,
172 REPLY_WIPAN_PARAMS = 0xb2,
173 REPLY_WIPAN_RXON = 0xb3, /* use REPLY_RXON structure */
174 REPLY_WIPAN_RXON_TIMING = 0xb4, /* use REPLY_RXON_TIMING structure */
175 REPLY_WIPAN_RXON_ASSOC = 0xb6, /* use REPLY_RXON_ASSOC structure */
176 REPLY_WIPAN_QOS_PARAM = 0xb7, /* use REPLY_QOS_PARAM structure */
177 REPLY_WIPAN_WEPKEY = 0xb8, /* use REPLY_WEPKEY structure */
178 REPLY_WIPAN_P2P_CHANNEL_SWITCH = 0xb9,
179 REPLY_WIPAN_NOA_NOTIFICATION = 0xbc,
180 REPLY_WIPAN_DEACTIVATION_COMPLETE = 0xbd,
182 REPLY_WOWLAN_PATTERNS = 0xe0,
183 REPLY_WOWLAN_WAKEUP_FILTER = 0xe1,
184 REPLY_WOWLAN_TSC_RSC_PARAMS = 0xe2,
185 REPLY_WOWLAN_TKIP_PARAMS = 0xe3,
186 REPLY_WOWLAN_KEK_KCK_MATERIAL = 0xe4,
187 REPLY_WOWLAN_GET_STATUS = 0xe5,
188 REPLY_D3_CONFIG = 0xd3,
194 * Minimum number of queues. MAX_NUM is defined in hw specific files.
195 * Set the minimum to accommodate
196 * - 4 standard TX queues
197 * - the command queue
199 * - the PAN multicast queue, and
200 * - the AUX (TX during scan dwell) queue.
202 #define IWL_MIN_NUM_QUEUES 11
205 * Command queue depends on iPAN support.
207 #define IWL_DEFAULT_CMD_QUEUE_NUM 4
208 #define IWL_IPAN_CMD_QUEUE_NUM 9
210 #define IWL_TX_FIFO_BK 0 /* shared */
211 #define IWL_TX_FIFO_BE 1
212 #define IWL_TX_FIFO_VI 2 /* shared */
213 #define IWL_TX_FIFO_VO 3
214 #define IWL_TX_FIFO_BK_IPAN IWL_TX_FIFO_BK
215 #define IWL_TX_FIFO_BE_IPAN 4
216 #define IWL_TX_FIFO_VI_IPAN IWL_TX_FIFO_VI
217 #define IWL_TX_FIFO_VO_IPAN 5
218 /* re-uses the VO FIFO, uCode will properly flush/schedule */
219 #define IWL_TX_FIFO_AUX 5
220 #define IWL_TX_FIFO_UNUSED 255
222 #define IWLAGN_CMD_FIFO_NUM 7
225 * This queue number is required for proper operation
226 * because the ucode will stop/start the scheduler as
229 #define IWL_IPAN_MCAST_QUEUE 8
231 /******************************************************************************
233 * Commonly used structures and definitions:
234 * Command header, rate_n_flags, txpower
236 *****************************************************************************/
239 * iwlagn rate_n_flags bit fields
241 * rate_n_flags format is used in following iwlagn commands:
242 * REPLY_RX (response only)
243 * REPLY_RX_MPDU (response only)
244 * REPLY_TX (both command and response)
245 * REPLY_TX_LINK_QUALITY_CMD
247 * High-throughput (HT) rate format for bits 7:0 (bit 8 must be "1"):
257 * 4-3: 0) Single stream (SISO)
258 * 1) Dual stream (MIMO)
259 * 2) Triple stream (MIMO)
261 * 5: Value of 0x20 in bits 7:0 indicates 6 Mbps HT40 duplicate data
263 * Legacy OFDM rate format for bits 7:0 (bit 8 must be "0", bit 9 "0"):
273 * Legacy CCK rate format for bits 7:0 (bit 8 must be "0", bit 9 "1"):
279 #define RATE_MCS_CODE_MSK 0x7
280 #define RATE_MCS_SPATIAL_POS 3
281 #define RATE_MCS_SPATIAL_MSK 0x18
282 #define RATE_MCS_HT_DUP_POS 5
283 #define RATE_MCS_HT_DUP_MSK 0x20
284 /* Both legacy and HT use bits 7:0 as the CCK/OFDM rate or HT MCS */
285 #define RATE_MCS_RATE_MSK 0xff
287 /* Bit 8: (1) HT format, (0) legacy format in bits 7:0 */
288 #define RATE_MCS_FLAGS_POS 8
289 #define RATE_MCS_HT_POS 8
290 #define RATE_MCS_HT_MSK 0x100
292 /* Bit 9: (1) CCK, (0) OFDM. HT (bit 8) must be "0" for this bit to be valid */
293 #define RATE_MCS_CCK_POS 9
294 #define RATE_MCS_CCK_MSK 0x200
296 /* Bit 10: (1) Use Green Field preamble */
297 #define RATE_MCS_GF_POS 10
298 #define RATE_MCS_GF_MSK 0x400
300 /* Bit 11: (1) Use 40Mhz HT40 chnl width, (0) use 20 MHz legacy chnl width */
301 #define RATE_MCS_HT40_POS 11
302 #define RATE_MCS_HT40_MSK 0x800
304 /* Bit 12: (1) Duplicate data on both 20MHz chnls. HT40 (bit 11) must be set. */
305 #define RATE_MCS_DUP_POS 12
306 #define RATE_MCS_DUP_MSK 0x1000
308 /* Bit 13: (1) Short guard interval (0.4 usec), (0) normal GI (0.8 usec) */
309 #define RATE_MCS_SGI_POS 13
310 #define RATE_MCS_SGI_MSK 0x2000
313 * rate_n_flags Tx antenna masks
316 #define RATE_MCS_ANT_POS 14
317 #define RATE_MCS_ANT_A_MSK 0x04000
318 #define RATE_MCS_ANT_B_MSK 0x08000
319 #define RATE_MCS_ANT_C_MSK 0x10000
320 #define RATE_MCS_ANT_AB_MSK (RATE_MCS_ANT_A_MSK | RATE_MCS_ANT_B_MSK)
321 #define RATE_MCS_ANT_ABC_MSK (RATE_MCS_ANT_AB_MSK | RATE_MCS_ANT_C_MSK)
322 #define RATE_ANT_NUM 3
324 #define POWER_TABLE_NUM_ENTRIES 33
325 #define POWER_TABLE_NUM_HT_OFDM_ENTRIES 32
326 #define POWER_TABLE_CCK_ENTRY 32
328 #define IWL_PWR_NUM_HT_OFDM_ENTRIES 24
329 #define IWL_PWR_CCK_ENTRIES 2
332 * struct tx_power_dual_stream
334 * Table entries in REPLY_TX_PWR_TABLE_CMD, REPLY_CHANNEL_SWITCH
336 * Same format as iwl_tx_power_dual_stream, but __le32
338 struct tx_power_dual_stream {
343 * Command REPLY_TX_POWER_DBM_CMD = 0x98
344 * struct iwlagn_tx_power_dbm_cmd
346 #define IWLAGN_TX_POWER_AUTO 0x7f
347 #define IWLAGN_TX_POWER_NO_CLOSED (0x1 << 6)
349 struct iwlagn_tx_power_dbm_cmd {
350 s8 global_lmt; /*in half-dBm (e.g. 30 = 15 dBm) */
352 s8 srv_chan_lmt; /*in half-dBm (e.g. 30 = 15 dBm) */
357 * Command TX_ANT_CONFIGURATION_CMD = 0x98
358 * This command is used to configure valid Tx antenna.
359 * By default uCode concludes the valid antenna according to the radio flavor.
360 * This command enables the driver to override/modify this conclusion.
362 struct iwl_tx_ant_config_cmd {
366 /******************************************************************************
368 * Alive and Error Commands & Responses:
370 *****************************************************************************/
372 #define UCODE_VALID_OK cpu_to_le32(0x1)
375 * REPLY_ALIVE = 0x1 (response only, not a command)
377 * uCode issues this "alive" notification once the runtime image is ready
378 * to receive commands from the driver. This is the *second* "alive"
379 * notification that the driver will receive after rebooting uCode;
380 * this "alive" is indicated by subtype field != 9.
382 * See comments documenting "BSM" (bootstrap state machine).
384 * This response includes two pointers to structures within the device's
385 * data SRAM (access via HBUS_TARG_MEM_* regs) that are useful for debugging:
387 * 1) log_event_table_ptr indicates base of the event log. This traces
388 * a 256-entry history of uCode execution within a circular buffer.
389 * Its header format is:
391 * __le32 log_size; log capacity (in number of entries)
392 * __le32 type; (1) timestamp with each entry, (0) no timestamp
393 * __le32 wraps; # times uCode has wrapped to top of circular buffer
394 * __le32 write_index; next circular buffer entry that uCode would fill
396 * The header is followed by the circular buffer of log entries. Entries
397 * with timestamps have the following format:
399 * __le32 event_id; range 0 - 1500
400 * __le32 timestamp; low 32 bits of TSF (of network, if associated)
401 * __le32 data; event_id-specific data value
403 * Entries without timestamps contain only event_id and data.
406 * 2) error_event_table_ptr indicates base of the error log. This contains
407 * information about any uCode error that occurs. For agn, the format
408 * of the error log is defined by struct iwl_error_event_table.
410 * The Linux driver can print both logs to the system log when a uCode error
415 * Note: This structure is read from the device with IO accesses,
416 * and the reading already does the endian conversion. As it is
417 * read with u32-sized accesses, any members with a different size
418 * need to be ordered correctly though!
420 struct iwl_error_event_table {
421 u32 valid; /* (nonzero) valid, (0) log is empty */
422 u32 error_id; /* type of error */
423 u32 pc; /* program counter */
424 u32 blink1; /* branch link */
425 u32 blink2; /* branch link */
426 u32 ilink1; /* interrupt link */
427 u32 ilink2; /* interrupt link */
428 u32 data1; /* error-specific data */
429 u32 data2; /* error-specific data */
430 u32 line; /* source code line of error */
431 u32 bcon_time; /* beacon timer */
432 u32 tsf_low; /* network timestamp function timer */
433 u32 tsf_hi; /* network timestamp function timer */
434 u32 gp1; /* GP1 timer register */
435 u32 gp2; /* GP2 timer register */
436 u32 gp3; /* GP3 timer register */
437 u32 ucode_ver; /* uCode version */
438 u32 hw_ver; /* HW Silicon version */
439 u32 brd_ver; /* HW board version */
440 u32 log_pc; /* log program counter */
441 u32 frame_ptr; /* frame pointer */
442 u32 stack_ptr; /* stack pointer */
443 u32 hcmd; /* last host command header */
444 u32 isr0; /* isr status register LMPM_NIC_ISR0:
446 u32 isr1; /* isr status register LMPM_NIC_ISR1:
448 u32 isr2; /* isr status register LMPM_NIC_ISR2:
450 u32 isr3; /* isr status register LMPM_NIC_ISR3:
452 u32 isr4; /* isr status register LMPM_NIC_ISR4:
454 u32 isr_pref; /* isr status register LMPM_NIC_PREF_STAT */
455 u32 wait_event; /* wait event() caller address */
456 u32 l2p_control; /* L2pControlField */
457 u32 l2p_duration; /* L2pDurationField */
458 u32 l2p_mhvalid; /* L2pMhValidBits */
459 u32 l2p_addr_match; /* L2pAddrMatchStat */
460 u32 lmpm_pmg_sel; /* indicate which clocks are turned on
462 u32 u_timestamp; /* indicate when the date and time of the
464 u32 flow_handler; /* FH read/write pointers, RX credit */
467 struct iwl_alive_resp {
473 u8 ver_subtype; /* not "9" for runtime alive */
475 __le32 log_event_table_ptr; /* SRAM address for event log */
476 __le32 error_event_table_ptr; /* SRAM address for error log */
482 * REPLY_ERROR = 0x2 (response only, not a command)
484 struct iwl_error_resp {
488 __le16 bad_cmd_seq_num;
493 /******************************************************************************
495 * RXON Commands & Responses:
497 *****************************************************************************/
500 * Rx config defines & structure
502 /* rx_config device types */
504 RXON_DEV_TYPE_AP = 1,
505 RXON_DEV_TYPE_ESS = 3,
506 RXON_DEV_TYPE_IBSS = 4,
507 RXON_DEV_TYPE_SNIFFER = 6,
508 RXON_DEV_TYPE_CP = 7,
509 RXON_DEV_TYPE_2STA = 8,
510 RXON_DEV_TYPE_P2P = 9,
514 #define RXON_RX_CHAIN_DRIVER_FORCE_MSK cpu_to_le16(0x1 << 0)
515 #define RXON_RX_CHAIN_DRIVER_FORCE_POS (0)
516 #define RXON_RX_CHAIN_VALID_MSK cpu_to_le16(0x7 << 1)
517 #define RXON_RX_CHAIN_VALID_POS (1)
518 #define RXON_RX_CHAIN_FORCE_SEL_MSK cpu_to_le16(0x7 << 4)
519 #define RXON_RX_CHAIN_FORCE_SEL_POS (4)
520 #define RXON_RX_CHAIN_FORCE_MIMO_SEL_MSK cpu_to_le16(0x7 << 7)
521 #define RXON_RX_CHAIN_FORCE_MIMO_SEL_POS (7)
522 #define RXON_RX_CHAIN_CNT_MSK cpu_to_le16(0x3 << 10)
523 #define RXON_RX_CHAIN_CNT_POS (10)
524 #define RXON_RX_CHAIN_MIMO_CNT_MSK cpu_to_le16(0x3 << 12)
525 #define RXON_RX_CHAIN_MIMO_CNT_POS (12)
526 #define RXON_RX_CHAIN_MIMO_FORCE_MSK cpu_to_le16(0x1 << 14)
527 #define RXON_RX_CHAIN_MIMO_FORCE_POS (14)
529 /* rx_config flags */
530 /* band & modulation selection */
531 #define RXON_FLG_BAND_24G_MSK cpu_to_le32(1 << 0)
532 #define RXON_FLG_CCK_MSK cpu_to_le32(1 << 1)
533 /* auto detection enable */
534 #define RXON_FLG_AUTO_DETECT_MSK cpu_to_le32(1 << 2)
535 /* TGg protection when tx */
536 #define RXON_FLG_TGG_PROTECT_MSK cpu_to_le32(1 << 3)
537 /* cck short slot & preamble */
538 #define RXON_FLG_SHORT_SLOT_MSK cpu_to_le32(1 << 4)
539 #define RXON_FLG_SHORT_PREAMBLE_MSK cpu_to_le32(1 << 5)
540 /* antenna selection */
541 #define RXON_FLG_DIS_DIV_MSK cpu_to_le32(1 << 7)
542 #define RXON_FLG_ANT_SEL_MSK cpu_to_le32(0x0f00)
543 #define RXON_FLG_ANT_A_MSK cpu_to_le32(1 << 8)
544 #define RXON_FLG_ANT_B_MSK cpu_to_le32(1 << 9)
545 /* radar detection enable */
546 #define RXON_FLG_RADAR_DETECT_MSK cpu_to_le32(1 << 12)
547 #define RXON_FLG_TGJ_NARROW_BAND_MSK cpu_to_le32(1 << 13)
548 /* rx response to host with 8-byte TSF
549 * (according to ON_AIR deassertion) */
550 #define RXON_FLG_TSF2HOST_MSK cpu_to_le32(1 << 15)
554 #define RXON_FLG_CTRL_CHANNEL_LOC_POS (22)
555 #define RXON_FLG_CTRL_CHANNEL_LOC_HI_MSK cpu_to_le32(0x1 << 22)
557 #define RXON_FLG_HT_OPERATING_MODE_POS (23)
559 #define RXON_FLG_HT_PROT_MSK cpu_to_le32(0x1 << 23)
560 #define RXON_FLG_HT40_PROT_MSK cpu_to_le32(0x2 << 23)
562 #define RXON_FLG_CHANNEL_MODE_POS (25)
563 #define RXON_FLG_CHANNEL_MODE_MSK cpu_to_le32(0x3 << 25)
567 CHANNEL_MODE_LEGACY = 0,
568 CHANNEL_MODE_PURE_40 = 1,
569 CHANNEL_MODE_MIXED = 2,
570 CHANNEL_MODE_RESERVED = 3,
572 #define RXON_FLG_CHANNEL_MODE_LEGACY cpu_to_le32(CHANNEL_MODE_LEGACY << RXON_FLG_CHANNEL_MODE_POS)
573 #define RXON_FLG_CHANNEL_MODE_PURE_40 cpu_to_le32(CHANNEL_MODE_PURE_40 << RXON_FLG_CHANNEL_MODE_POS)
574 #define RXON_FLG_CHANNEL_MODE_MIXED cpu_to_le32(CHANNEL_MODE_MIXED << RXON_FLG_CHANNEL_MODE_POS)
576 /* CTS to self (if spec allows) flag */
577 #define RXON_FLG_SELF_CTS_EN cpu_to_le32(0x1<<30)
579 /* rx_config filter flags */
580 /* accept all data frames */
581 #define RXON_FILTER_PROMISC_MSK cpu_to_le32(1 << 0)
582 /* pass control & management to host */
583 #define RXON_FILTER_CTL2HOST_MSK cpu_to_le32(1 << 1)
584 /* accept multi-cast */
585 #define RXON_FILTER_ACCEPT_GRP_MSK cpu_to_le32(1 << 2)
586 /* don't decrypt uni-cast frames */
587 #define RXON_FILTER_DIS_DECRYPT_MSK cpu_to_le32(1 << 3)
588 /* don't decrypt multi-cast frames */
589 #define RXON_FILTER_DIS_GRP_DECRYPT_MSK cpu_to_le32(1 << 4)
590 /* STA is associated */
591 #define RXON_FILTER_ASSOC_MSK cpu_to_le32(1 << 5)
592 /* transfer to host non bssid beacons in associated state */
593 #define RXON_FILTER_BCON_AWARE_MSK cpu_to_le32(1 << 6)
596 * REPLY_RXON = 0x10 (command, has simple generic response)
598 * RXON tunes the radio tuner to a service channel, and sets up a number
599 * of parameters that are used primarily for Rx, but also for Tx operations.
601 * NOTE: When tuning to a new channel, driver must set the
602 * RXON_FILTER_ASSOC_MSK to 0. This will clear station-dependent
603 * info within the device, including the station tables, tx retry
604 * rate tables, and txpower tables. Driver must build a new station
605 * table and txpower table before transmitting anything on the RXON
608 * NOTE: All RXONs wipe clean the internal txpower table. Driver must
609 * issue a new REPLY_TX_PWR_TABLE_CMD after each REPLY_RXON (0x10),
610 * regardless of whether RXON_FILTER_ASSOC_MSK is set.
613 struct iwl_rxon_cmd {
618 u8 wlap_bssid_addr[6];
629 u8 ofdm_ht_single_stream_basic_rates;
630 u8 ofdm_ht_dual_stream_basic_rates;
631 u8 ofdm_ht_triple_stream_basic_rates;
633 __le16 acquisition_data;
638 * REPLY_RXON_ASSOC = 0x11 (command, has simple generic response)
640 struct iwl_rxon_assoc_cmd {
646 u8 ofdm_ht_single_stream_basic_rates;
647 u8 ofdm_ht_dual_stream_basic_rates;
648 u8 ofdm_ht_triple_stream_basic_rates;
650 __le16 rx_chain_select_flags;
651 __le16 acquisition_data;
655 #define IWL_CONN_MAX_LISTEN_INTERVAL 10
656 #define IWL_MAX_UCODE_BEACON_INTERVAL 4 /* 4096 */
659 * REPLY_RXON_TIMING = 0x14 (command, has simple generic response)
661 struct iwl_rxon_time_cmd {
663 __le16 beacon_interval;
665 __le32 beacon_init_val;
666 __le16 listen_interval;
668 u8 delta_cp_bss_tbtts;
672 * REPLY_CHANNEL_SWITCH = 0x72 (command, has simple generic response)
675 * struct iwl5000_channel_switch_cmd
676 * @band: 0- 5.2GHz, 1- 2.4GHz
677 * @expect_beacon: 0- resume transmits after channel switch
678 * 1- wait for beacon to resume transmits
679 * @channel: new channel number
680 * @rxon_flags: Rx on flags
681 * @rxon_filter_flags: filtering parameters
682 * @switch_time: switch time in extended beacon format
683 * @reserved: reserved bytes
685 struct iwl5000_channel_switch_cmd {
690 __le32 rxon_filter_flags;
692 __le32 reserved[2][IWL_PWR_NUM_HT_OFDM_ENTRIES + IWL_PWR_CCK_ENTRIES];
696 * struct iwl6000_channel_switch_cmd
697 * @band: 0- 5.2GHz, 1- 2.4GHz
698 * @expect_beacon: 0- resume transmits after channel switch
699 * 1- wait for beacon to resume transmits
700 * @channel: new channel number
701 * @rxon_flags: Rx on flags
702 * @rxon_filter_flags: filtering parameters
703 * @switch_time: switch time in extended beacon format
704 * @reserved: reserved bytes
706 struct iwl6000_channel_switch_cmd {
711 __le32 rxon_filter_flags;
713 __le32 reserved[3][IWL_PWR_NUM_HT_OFDM_ENTRIES + IWL_PWR_CCK_ENTRIES];
717 * CHANNEL_SWITCH_NOTIFICATION = 0x73 (notification only, not a command)
719 struct iwl_csa_notification {
722 __le32 status; /* 0 - OK, 1 - fail */
725 /******************************************************************************
727 * Quality-of-Service (QOS) Commands & Responses:
729 *****************************************************************************/
732 * struct iwl_ac_qos -- QOS timing params for REPLY_QOS_PARAM
733 * One for each of 4 EDCA access categories in struct iwl_qosparam_cmd
735 * @cw_min: Contention window, start value in numbers of slots.
736 * Should be a power-of-2, minus 1. Device's default is 0x0f.
737 * @cw_max: Contention window, max value in numbers of slots.
738 * Should be a power-of-2, minus 1. Device's default is 0x3f.
739 * @aifsn: Number of slots in Arbitration Interframe Space (before
740 * performing random backoff timing prior to Tx). Device default 1.
741 * @edca_txop: Length of Tx opportunity, in uSecs. Device default is 0.
743 * Device will automatically increase contention window by (2*CW) + 1 for each
744 * transmission retry. Device uses cw_max as a bit mask, ANDed with new CW
745 * value, to cap the CW value.
755 /* QoS flags defines */
756 #define QOS_PARAM_FLG_UPDATE_EDCA_MSK cpu_to_le32(0x01)
757 #define QOS_PARAM_FLG_TGN_MSK cpu_to_le32(0x02)
758 #define QOS_PARAM_FLG_TXOP_TYPE_MSK cpu_to_le32(0x10)
760 /* Number of Access Categories (AC) (EDCA), queues 0..3 */
764 * REPLY_QOS_PARAM = 0x13 (command, has simple generic response)
766 * This command sets up timings for each of the 4 prioritized EDCA Tx FIFOs
767 * 0: Background, 1: Best Effort, 2: Video, 3: Voice.
769 struct iwl_qosparam_cmd {
771 struct iwl_ac_qos ac[AC_NUM];
774 /******************************************************************************
776 * Add/Modify Stations Commands & Responses:
778 *****************************************************************************/
780 * Multi station support
783 /* Special, dedicated locations within device's station table */
785 #define IWL_AP_ID_PAN 1
787 #define IWLAGN_PAN_BCAST_ID 14
788 #define IWLAGN_BROADCAST_ID 15
789 #define IWLAGN_STATION_COUNT 16
791 #define IWL_TID_NON_QOS IWL_MAX_TID_COUNT
793 #define STA_FLG_TX_RATE_MSK cpu_to_le32(1 << 2)
794 #define STA_FLG_PWR_SAVE_MSK cpu_to_le32(1 << 8)
795 #define STA_FLG_PAN_STATION cpu_to_le32(1 << 13)
796 #define STA_FLG_RTS_MIMO_PROT_MSK cpu_to_le32(1 << 17)
797 #define STA_FLG_AGG_MPDU_8US_MSK cpu_to_le32(1 << 18)
798 #define STA_FLG_MAX_AGG_SIZE_POS (19)
799 #define STA_FLG_MAX_AGG_SIZE_MSK cpu_to_le32(3 << 19)
800 #define STA_FLG_HT40_EN_MSK cpu_to_le32(1 << 21)
801 #define STA_FLG_MIMO_DIS_MSK cpu_to_le32(1 << 22)
802 #define STA_FLG_AGG_MPDU_DENSITY_POS (23)
803 #define STA_FLG_AGG_MPDU_DENSITY_MSK cpu_to_le32(7 << 23)
805 /* Use in mode field. 1: modify existing entry, 0: add new station entry */
806 #define STA_CONTROL_MODIFY_MSK 0x01
808 /* key flags __le16*/
809 #define STA_KEY_FLG_ENCRYPT_MSK cpu_to_le16(0x0007)
810 #define STA_KEY_FLG_NO_ENC cpu_to_le16(0x0000)
811 #define STA_KEY_FLG_WEP cpu_to_le16(0x0001)
812 #define STA_KEY_FLG_CCMP cpu_to_le16(0x0002)
813 #define STA_KEY_FLG_TKIP cpu_to_le16(0x0003)
815 #define STA_KEY_FLG_KEYID_POS 8
816 #define STA_KEY_FLG_INVALID cpu_to_le16(0x0800)
817 /* wep key is either from global key (0) or from station info array (1) */
818 #define STA_KEY_FLG_MAP_KEY_MSK cpu_to_le16(0x0008)
820 /* wep key in STA: 5-bytes (0) or 13-bytes (1) */
821 #define STA_KEY_FLG_KEY_SIZE_MSK cpu_to_le16(0x1000)
822 #define STA_KEY_MULTICAST_MSK cpu_to_le16(0x4000)
823 #define STA_KEY_MAX_NUM 8
824 #define STA_KEY_MAX_NUM_PAN 16
825 /* must not match WEP_INVALID_OFFSET */
826 #define IWLAGN_HW_KEY_DEFAULT 0xfe
828 /* Flags indicate whether to modify vs. don't change various station params */
829 #define STA_MODIFY_KEY_MASK 0x01
830 #define STA_MODIFY_TID_DISABLE_TX 0x02
831 #define STA_MODIFY_TX_RATE_MSK 0x04
832 #define STA_MODIFY_ADDBA_TID_MSK 0x08
833 #define STA_MODIFY_DELBA_TID_MSK 0x10
834 #define STA_MODIFY_SLEEP_TX_COUNT_MSK 0x20
839 u8 tkip_rx_tsc_byte2; /* TSC[2] for key mix ph1 detection */
841 __le16 tkip_rx_ttak[5]; /* 10-byte unicast TKIP TTAK */
844 u8 key[16]; /* 16-byte unicast decryption key */
845 __le64 tx_secur_seq_cnt;
846 __le64 hw_tkip_mic_rx_key;
847 __le64 hw_tkip_mic_tx_key;
851 * struct sta_id_modify
852 * @addr[ETH_ALEN]: station's MAC address
853 * @sta_id: index of station in uCode's station table
854 * @modify_mask: STA_MODIFY_*, 1: modify, 0: don't change
856 * Driver selects unused table index when adding new station,
857 * or the index to a pre-existing station entry when modifying that station.
858 * Some indexes have special purposes (IWL_AP_ID, index 0, is for AP).
860 * modify_mask flags select which parameters to modify vs. leave alone.
862 struct sta_id_modify {
871 * REPLY_ADD_STA = 0x18 (command)
873 * The device contains an internal table of per-station information,
874 * with info on security keys, aggregation parameters, and Tx rates for
875 * initial Tx attempt and any retries (agn devices uses
876 * REPLY_TX_LINK_QUALITY_CMD,
878 * REPLY_ADD_STA sets up the table entry for one station, either creating
879 * a new entry, or modifying a pre-existing one.
881 * NOTE: RXON command (without "associated" bit set) wipes the station table
882 * clean. Moving into RF_KILL state does this also. Driver must set up
883 * new station table before transmitting anything on the RXON channel
884 * (except active scans or active measurements; those commands carry
885 * their own txpower/rate setup data).
887 * When getting started on a new channel, driver must set up the
888 * IWL_BROADCAST_ID entry (last entry in the table). For a client
889 * station in a BSS, once an AP is selected, driver sets up the AP STA
890 * in the IWL_AP_ID entry (1st entry in the table). BROADCAST and AP
891 * are all that are needed for a BSS client station. If the device is
892 * used as AP, or in an IBSS network, driver must set up station table
893 * entries for all STAs in network, starting with index IWL_STA_ID.
896 struct iwl_addsta_cmd {
897 u8 mode; /* 1: modify existing, 0: add new station */
899 struct sta_id_modify sta;
900 struct iwl_keyinfo key;
901 __le32 station_flags; /* STA_FLG_* */
902 __le32 station_flags_msk; /* STA_FLG_* */
904 /* bit field to disable (1) or enable (0) Tx for Traffic ID (TID)
905 * corresponding to bit (e.g. bit 5 controls TID 5).
906 * Set modify_mask bit STA_MODIFY_TID_DISABLE_TX to use this field. */
907 __le16 tid_disable_tx;
908 __le16 legacy_reserved;
910 /* TID for which to add block-ack support.
911 * Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
912 u8 add_immediate_ba_tid;
914 /* TID for which to remove block-ack support.
915 * Set modify_mask bit STA_MODIFY_DELBA_TID_MSK to use this field. */
916 u8 remove_immediate_ba_tid;
918 /* Starting Sequence Number for added block-ack support.
919 * Set modify_mask bit STA_MODIFY_ADDBA_TID_MSK to use this field. */
920 __le16 add_immediate_ba_ssn;
923 * Number of packets OK to transmit to station even though
924 * it is asleep -- used to synchronise PS-poll and u-APSD
925 * responses while ucode keeps track of STA sleep state.
927 __le16 sleep_tx_count;
933 #define ADD_STA_SUCCESS_MSK 0x1
934 #define ADD_STA_NO_ROOM_IN_TABLE 0x2
935 #define ADD_STA_NO_BLOCK_ACK_RESOURCE 0x4
936 #define ADD_STA_MODIFY_NON_EXIST_STA 0x8
938 * REPLY_ADD_STA = 0x18 (response)
940 struct iwl_add_sta_resp {
941 u8 status; /* ADD_STA_* */
944 #define REM_STA_SUCCESS_MSK 0x1
946 * REPLY_REM_STA = 0x19 (response)
948 struct iwl_rem_sta_resp {
953 * REPLY_REM_STA = 0x19 (command)
955 struct iwl_rem_sta_cmd {
956 u8 num_sta; /* number of removed stations */
958 u8 addr[ETH_ALEN]; /* MAC addr of the first station */
963 /* WiFi queues mask */
964 #define IWL_SCD_BK_MSK BIT(0)
965 #define IWL_SCD_BE_MSK BIT(1)
966 #define IWL_SCD_VI_MSK BIT(2)
967 #define IWL_SCD_VO_MSK BIT(3)
968 #define IWL_SCD_MGMT_MSK BIT(3)
970 /* PAN queues mask */
971 #define IWL_PAN_SCD_BK_MSK BIT(4)
972 #define IWL_PAN_SCD_BE_MSK BIT(5)
973 #define IWL_PAN_SCD_VI_MSK BIT(6)
974 #define IWL_PAN_SCD_VO_MSK BIT(7)
975 #define IWL_PAN_SCD_MGMT_MSK BIT(7)
976 #define IWL_PAN_SCD_MULTICAST_MSK BIT(8)
978 #define IWL_AGG_TX_QUEUE_MSK 0xffc00
980 #define IWL_DROP_ALL BIT(1)
983 * REPLY_TXFIFO_FLUSH = 0x1e(command and response)
985 * When using full FIFO flush this command checks the scheduler HW block WR/RD
986 * pointers to check if all the frames were transferred by DMA into the
987 * relevant TX FIFO queue. Only when the DMA is finished and the queue is
988 * empty the command can finish.
989 * This command is used to flush the TXFIFO from transmit commands, it may
990 * operate on single or multiple queues, the command queue can't be flushed by
991 * this command. The command response is returned when all the queue flush
992 * operations are done. Each TX command flushed return response with the FLUSH
993 * status set in the TX response status. When FIFO flush operation is used,
994 * the flush operation ends when both the scheduler DMA done and TXFIFO empty
997 * @queue_control: bit mask for which queues to flush
998 * @flush_control: flush controls
999 * 0: Dump single MSDU
1000 * 1: Dump multiple MSDU according to PS, INVALID STA, TTL, TID disable.
1003 struct iwl_txfifo_flush_cmd_v3 {
1004 __le32 queue_control;
1005 __le16 flush_control;
1009 struct iwl_txfifo_flush_cmd_v2 {
1010 __le16 queue_control;
1011 __le16 flush_control;
1015 * REPLY_WEP_KEY = 0x20
1017 struct iwl_wep_key {
1026 struct iwl_wep_cmd {
1031 struct iwl_wep_key key[0];
1034 #define WEP_KEY_WEP_TYPE 1
1035 #define WEP_KEYS_MAX 4
1036 #define WEP_INVALID_OFFSET 0xff
1037 #define WEP_KEY_LEN_64 5
1038 #define WEP_KEY_LEN_128 13
1040 /******************************************************************************
1044 *****************************************************************************/
1046 #define RX_RES_STATUS_NO_CRC32_ERROR cpu_to_le32(1 << 0)
1047 #define RX_RES_STATUS_NO_RXE_OVERFLOW cpu_to_le32(1 << 1)
1049 #define RX_RES_PHY_FLAGS_BAND_24_MSK cpu_to_le16(1 << 0)
1050 #define RX_RES_PHY_FLAGS_MOD_CCK_MSK cpu_to_le16(1 << 1)
1051 #define RX_RES_PHY_FLAGS_SHORT_PREAMBLE_MSK cpu_to_le16(1 << 2)
1052 #define RX_RES_PHY_FLAGS_NARROW_BAND_MSK cpu_to_le16(1 << 3)
1053 #define RX_RES_PHY_FLAGS_ANTENNA_MSK 0x70
1054 #define RX_RES_PHY_FLAGS_ANTENNA_POS 4
1055 #define RX_RES_PHY_FLAGS_AGG_MSK cpu_to_le16(1 << 7)
1057 #define RX_RES_STATUS_SEC_TYPE_MSK (0x7 << 8)
1058 #define RX_RES_STATUS_SEC_TYPE_NONE (0x0 << 8)
1059 #define RX_RES_STATUS_SEC_TYPE_WEP (0x1 << 8)
1060 #define RX_RES_STATUS_SEC_TYPE_CCMP (0x2 << 8)
1061 #define RX_RES_STATUS_SEC_TYPE_TKIP (0x3 << 8)
1062 #define RX_RES_STATUS_SEC_TYPE_ERR (0x7 << 8)
1064 #define RX_RES_STATUS_STATION_FOUND (1<<6)
1065 #define RX_RES_STATUS_NO_STATION_INFO_MISMATCH (1<<7)
1067 #define RX_RES_STATUS_DECRYPT_TYPE_MSK (0x3 << 11)
1068 #define RX_RES_STATUS_NOT_DECRYPT (0x0 << 11)
1069 #define RX_RES_STATUS_DECRYPT_OK (0x3 << 11)
1070 #define RX_RES_STATUS_BAD_ICV_MIC (0x1 << 11)
1071 #define RX_RES_STATUS_BAD_KEY_TTAK (0x2 << 11)
1073 #define RX_MPDU_RES_STATUS_ICV_OK (0x20)
1074 #define RX_MPDU_RES_STATUS_MIC_OK (0x40)
1075 #define RX_MPDU_RES_STATUS_TTAK_OK (1 << 7)
1076 #define RX_MPDU_RES_STATUS_DEC_DONE_MSK (0x800)
1079 #define IWLAGN_RX_RES_PHY_CNT 8
1080 #define IWLAGN_RX_RES_AGC_IDX 1
1081 #define IWLAGN_RX_RES_RSSI_AB_IDX 2
1082 #define IWLAGN_RX_RES_RSSI_C_IDX 3
1083 #define IWLAGN_OFDM_AGC_MSK 0xfe00
1084 #define IWLAGN_OFDM_AGC_BIT_POS 9
1085 #define IWLAGN_OFDM_RSSI_INBAND_A_BITMSK 0x00ff
1086 #define IWLAGN_OFDM_RSSI_ALLBAND_A_BITMSK 0xff00
1087 #define IWLAGN_OFDM_RSSI_A_BIT_POS 0
1088 #define IWLAGN_OFDM_RSSI_INBAND_B_BITMSK 0xff0000
1089 #define IWLAGN_OFDM_RSSI_ALLBAND_B_BITMSK 0xff000000
1090 #define IWLAGN_OFDM_RSSI_B_BIT_POS 16
1091 #define IWLAGN_OFDM_RSSI_INBAND_C_BITMSK 0x00ff
1092 #define IWLAGN_OFDM_RSSI_ALLBAND_C_BITMSK 0xff00
1093 #define IWLAGN_OFDM_RSSI_C_BIT_POS 0
1095 struct iwlagn_non_cfg_phy {
1096 __le32 non_cfg_phy[IWLAGN_RX_RES_PHY_CNT]; /* up to 8 phy entries */
1101 * REPLY_RX = 0xc3 (response only, not a command)
1102 * Used only for legacy (non 11n) frames.
1104 struct iwl_rx_phy_res {
1105 u8 non_cfg_phy_cnt; /* non configurable DSP phy data byte count */
1106 u8 cfg_phy_cnt; /* configurable DSP phy data byte count */
1107 u8 stat_id; /* configurable DSP phy data set ID */
1109 __le64 timestamp; /* TSF at on air rise */
1110 __le32 beacon_time_stamp; /* beacon at on-air rise */
1111 __le16 phy_flags; /* general phy flags: band, modulation, ... */
1112 __le16 channel; /* channel number */
1113 u8 non_cfg_phy_buf[32]; /* for various implementations of non_cfg_phy */
1114 __le32 rate_n_flags; /* RATE_MCS_* */
1115 __le16 byte_count; /* frame's byte-count */
1116 __le16 frame_time; /* frame's time on the air */
1119 struct iwl_rx_mpdu_res_start {
1125 /******************************************************************************
1127 * Tx Commands & Responses:
1129 * Driver must place each REPLY_TX command into one of the prioritized Tx
1130 * queues in host DRAM, shared between driver and device (see comments for
1131 * SCD registers and Tx/Rx Queues). When the device's Tx scheduler and uCode
1132 * are preparing to transmit, the device pulls the Tx command over the PCI
1133 * bus via one of the device's Tx DMA channels, to fill an internal FIFO
1134 * from which data will be transmitted.
1136 * uCode handles all timing and protocol related to control frames
1137 * (RTS/CTS/ACK), based on flags in the Tx command. uCode and Tx scheduler
1138 * handle reception of block-acks; uCode updates the host driver via
1139 * REPLY_COMPRESSED_BA.
1141 * uCode handles retrying Tx when an ACK is expected but not received.
1142 * This includes trying lower data rates than the one requested in the Tx
1143 * command, as set up by the REPLY_TX_LINK_QUALITY_CMD (agn).
1145 * Driver sets up transmit power for various rates via REPLY_TX_PWR_TABLE_CMD.
1146 * This command must be executed after every RXON command, before Tx can occur.
1147 *****************************************************************************/
1149 /* REPLY_TX Tx flags field */
1152 * 1: Use RTS/CTS protocol or CTS-to-self if spec allows it
1153 * before this frame. if CTS-to-self required check
1154 * RXON_FLG_SELF_CTS_EN status.
1156 #define TX_CMD_FLG_PROT_REQUIRE_MSK cpu_to_le32(1 << 0)
1158 /* 1: Expect ACK from receiving station
1159 * 0: Don't expect ACK (MAC header's duration field s/b 0)
1160 * Set this for unicast frames, but not broadcast/multicast. */
1161 #define TX_CMD_FLG_ACK_MSK cpu_to_le32(1 << 3)
1164 * 1: Use rate scale table (see REPLY_TX_LINK_QUALITY_CMD).
1165 * Tx command's initial_rate_index indicates first rate to try;
1166 * uCode walks through table for additional Tx attempts.
1167 * 0: Use Tx rate/MCS from Tx command's rate_n_flags field.
1168 * This rate will be used for all Tx attempts; it will not be scaled. */
1169 #define TX_CMD_FLG_STA_RATE_MSK cpu_to_le32(1 << 4)
1171 /* 1: Expect immediate block-ack.
1172 * Set when Txing a block-ack request frame. Also set TX_CMD_FLG_ACK_MSK. */
1173 #define TX_CMD_FLG_IMM_BA_RSP_MASK cpu_to_le32(1 << 6)
1175 /* Tx antenna selection field; reserved (0) for agn devices. */
1176 #define TX_CMD_FLG_ANT_SEL_MSK cpu_to_le32(0xf00)
1178 /* 1: Ignore Bluetooth priority for this frame.
1179 * 0: Delay Tx until Bluetooth device is done (normal usage). */
1180 #define TX_CMD_FLG_IGNORE_BT cpu_to_le32(1 << 12)
1182 /* 1: uCode overrides sequence control field in MAC header.
1183 * 0: Driver provides sequence control field in MAC header.
1184 * Set this for management frames, non-QOS data frames, non-unicast frames,
1185 * and also in Tx command embedded in REPLY_SCAN_CMD for active scans. */
1186 #define TX_CMD_FLG_SEQ_CTL_MSK cpu_to_le32(1 << 13)
1188 /* 1: This frame is non-last MPDU; more fragments are coming.
1189 * 0: Last fragment, or not using fragmentation. */
1190 #define TX_CMD_FLG_MORE_FRAG_MSK cpu_to_le32(1 << 14)
1192 /* 1: uCode calculates and inserts Timestamp Function (TSF) in outgoing frame.
1193 * 0: No TSF required in outgoing frame.
1194 * Set this for transmitting beacons and probe responses. */
1195 #define TX_CMD_FLG_TSF_MSK cpu_to_le32(1 << 16)
1197 /* 1: Driver inserted 2 bytes pad after the MAC header, for (required) dword
1198 * alignment of frame's payload data field.
1200 * Set this for MAC headers with 26 or 30 bytes, i.e. those with QOS or ADDR4
1201 * field (but not both). Driver must align frame data (i.e. data following
1202 * MAC header) to DWORD boundary. */
1203 #define TX_CMD_FLG_MH_PAD_MSK cpu_to_le32(1 << 20)
1205 /* accelerate aggregation support
1206 * 0 - no CCMP encryption; 1 - CCMP encryption */
1207 #define TX_CMD_FLG_AGG_CCMP_MSK cpu_to_le32(1 << 22)
1209 /* HCCA-AP - disable duration overwriting. */
1210 #define TX_CMD_FLG_DUR_MSK cpu_to_le32(1 << 25)
1214 * TX command security control
1216 #define TX_CMD_SEC_WEP 0x01
1217 #define TX_CMD_SEC_CCM 0x02
1218 #define TX_CMD_SEC_TKIP 0x03
1219 #define TX_CMD_SEC_MSK 0x03
1220 #define TX_CMD_SEC_SHIFT 6
1221 #define TX_CMD_SEC_KEY128 0x08
1224 * REPLY_TX = 0x1c (command)
1228 * Used for managing Tx retries when expecting block-acks.
1229 * Driver should set these fields to 0.
1231 struct iwl_dram_scratch {
1232 u8 try_cnt; /* Tx attempts */
1233 u8 bt_kill_cnt; /* Tx attempts blocked by Bluetooth device */
1240 * MAC header (24/26/30/32 bytes) + 2 bytes pad if 26/30 header size,
1241 * + 8 byte IV for CCM or TKIP (not used for WEP)
1243 * + 8-byte MIC (not used for CCM/WEP)
1244 * NOTE: Does not include Tx command bytes, post-MAC pad bytes,
1245 * MIC (CCM) 8 bytes, ICV (WEP/TKIP/CKIP) 4 bytes, CRC 4 bytes.i
1246 * Range: 14-2342 bytes.
1251 * MPDU or MSDU byte count for next frame.
1252 * Used for fragmentation and bursting, but not 11n aggregation.
1253 * Same as "len", but for next frame. Set to 0 if not applicable.
1255 __le16 next_frame_len;
1257 __le32 tx_flags; /* TX_CMD_FLG_* */
1259 /* uCode may modify this field of the Tx command (in host DRAM!).
1260 * Driver must also set dram_lsb_ptr and dram_msb_ptr in this cmd. */
1261 struct iwl_dram_scratch scratch;
1263 /* Rate for *all* Tx attempts, if TX_CMD_FLG_STA_RATE_MSK is cleared. */
1264 __le32 rate_n_flags; /* RATE_MCS_* */
1266 /* Index of destination station in uCode's station table */
1269 /* Type of security encryption: CCM or TKIP */
1270 u8 sec_ctl; /* TX_CMD_SEC_* */
1273 * Index into rate table (see REPLY_TX_LINK_QUALITY_CMD) for initial
1274 * Tx attempt, if TX_CMD_FLG_STA_RATE_MSK is set. Normally "0" for
1275 * data frames, this field may be used to selectively reduce initial
1276 * rate (via non-0 value) for special frames (e.g. management), while
1277 * still supporting rate scaling for all frames.
1279 u8 initial_rate_index;
1282 __le16 next_frame_flags;
1289 /* Host DRAM physical address pointer to "scratch" in this command.
1290 * Must be dword aligned. "0" in dram_lsb_ptr disables usage. */
1291 __le32 dram_lsb_ptr;
1294 u8 rts_retry_limit; /*byte 50 */
1295 u8 data_retry_limit; /*byte 51 */
1298 __le16 pm_frame_timeout;
1299 __le16 attempt_duration;
1303 * Duration of EDCA burst Tx Opportunity, in 32-usec units.
1304 * Set this if txop time is not specified by HCCA protocol (e.g. by AP).
1309 * MAC header goes here, followed by 2 bytes padding if MAC header
1310 * length is 26 or 30 bytes, followed by payload data
1313 struct ieee80211_hdr hdr[0];
1317 * TX command response is sent after *agn* transmission attempts.
1319 * both postpone and abort status are expected behavior from uCode. there is
1320 * no special operation required from driver; except for RFKILL_FLUSH,
1321 * which required tx flush host command to flush all the tx frames in queues
1324 TX_STATUS_SUCCESS = 0x01,
1325 TX_STATUS_DIRECT_DONE = 0x02,
1327 TX_STATUS_POSTPONE_DELAY = 0x40,
1328 TX_STATUS_POSTPONE_FEW_BYTES = 0x41,
1329 TX_STATUS_POSTPONE_BT_PRIO = 0x42,
1330 TX_STATUS_POSTPONE_QUIET_PERIOD = 0x43,
1331 TX_STATUS_POSTPONE_CALC_TTAK = 0x44,
1333 TX_STATUS_FAIL_INTERNAL_CROSSED_RETRY = 0x81,
1334 TX_STATUS_FAIL_SHORT_LIMIT = 0x82,
1335 TX_STATUS_FAIL_LONG_LIMIT = 0x83,
1336 TX_STATUS_FAIL_FIFO_UNDERRUN = 0x84,
1337 TX_STATUS_FAIL_DRAIN_FLOW = 0x85,
1338 TX_STATUS_FAIL_RFKILL_FLUSH = 0x86,
1339 TX_STATUS_FAIL_LIFE_EXPIRE = 0x87,
1340 TX_STATUS_FAIL_DEST_PS = 0x88,
1341 TX_STATUS_FAIL_HOST_ABORTED = 0x89,
1342 TX_STATUS_FAIL_BT_RETRY = 0x8a,
1343 TX_STATUS_FAIL_STA_INVALID = 0x8b,
1344 TX_STATUS_FAIL_FRAG_DROPPED = 0x8c,
1345 TX_STATUS_FAIL_TID_DISABLE = 0x8d,
1346 TX_STATUS_FAIL_FIFO_FLUSHED = 0x8e,
1347 TX_STATUS_FAIL_INSUFFICIENT_CF_POLL = 0x8f,
1348 TX_STATUS_FAIL_PASSIVE_NO_RX = 0x90,
1349 TX_STATUS_FAIL_NO_BEACON_ON_RADAR = 0x91,
1352 #define TX_PACKET_MODE_REGULAR 0x0000
1353 #define TX_PACKET_MODE_BURST_SEQ 0x0100
1354 #define TX_PACKET_MODE_BURST_FIRST 0x0200
1357 TX_POWER_PA_NOT_ACTIVE = 0x0,
1361 TX_STATUS_MSK = 0x000000ff, /* bits 0:7 */
1362 TX_STATUS_DELAY_MSK = 0x00000040,
1363 TX_STATUS_ABORT_MSK = 0x00000080,
1364 TX_PACKET_MODE_MSK = 0x0000ff00, /* bits 8:15 */
1365 TX_FIFO_NUMBER_MSK = 0x00070000, /* bits 16:18 */
1366 TX_RESERVED = 0x00780000, /* bits 19:22 */
1367 TX_POWER_PA_DETECT_MSK = 0x7f800000, /* bits 23:30 */
1368 TX_ABORT_REQUIRED_MSK = 0x80000000, /* bits 31:31 */
1371 /* *******************************
1372 * TX aggregation status
1373 ******************************* */
1376 AGG_TX_STATE_TRANSMITTED = 0x00,
1377 AGG_TX_STATE_UNDERRUN_MSK = 0x01,
1378 AGG_TX_STATE_BT_PRIO_MSK = 0x02,
1379 AGG_TX_STATE_FEW_BYTES_MSK = 0x04,
1380 AGG_TX_STATE_ABORT_MSK = 0x08,
1381 AGG_TX_STATE_LAST_SENT_TTL_MSK = 0x10,
1382 AGG_TX_STATE_LAST_SENT_TRY_CNT_MSK = 0x20,
1383 AGG_TX_STATE_LAST_SENT_BT_KILL_MSK = 0x40,
1384 AGG_TX_STATE_SCD_QUERY_MSK = 0x80,
1385 AGG_TX_STATE_TEST_BAD_CRC32_MSK = 0x100,
1386 AGG_TX_STATE_RESPONSE_MSK = 0x1ff,
1387 AGG_TX_STATE_DUMP_TX_MSK = 0x200,
1388 AGG_TX_STATE_DELAY_TX_MSK = 0x400
1391 #define AGG_TX_STATUS_MSK 0x00000fff /* bits 0:11 */
1392 #define AGG_TX_TRY_MSK 0x0000f000 /* bits 12:15 */
1393 #define AGG_TX_TRY_POS 12
1395 #define AGG_TX_STATE_LAST_SENT_MSK (AGG_TX_STATE_LAST_SENT_TTL_MSK | \
1396 AGG_TX_STATE_LAST_SENT_TRY_CNT_MSK | \
1397 AGG_TX_STATE_LAST_SENT_BT_KILL_MSK)
1399 /* # tx attempts for first frame in aggregation */
1400 #define AGG_TX_STATE_TRY_CNT_POS 12
1401 #define AGG_TX_STATE_TRY_CNT_MSK 0xf000
1403 /* Command ID and sequence number of Tx command for this frame */
1404 #define AGG_TX_STATE_SEQ_NUM_POS 16
1405 #define AGG_TX_STATE_SEQ_NUM_MSK 0xffff0000
1408 * REPLY_TX = 0x1c (response)
1410 * This response may be in one of two slightly different formats, indicated
1411 * by the frame_count field:
1413 * 1) No aggregation (frame_count == 1). This reports Tx results for
1414 * a single frame. Multiple attempts, at various bit rates, may have
1415 * been made for this frame.
1417 * 2) Aggregation (frame_count > 1). This reports Tx results for
1418 * 2 or more frames that used block-acknowledge. All frames were
1419 * transmitted at same rate. Rate scaling may have been used if first
1420 * frame in this new agg block failed in previous agg block(s).
1422 * Note that, for aggregation, ACK (block-ack) status is not delivered here;
1423 * block-ack has not been received by the time the agn device records
1425 * This status relates to reasons the tx might have been blocked or aborted
1426 * within the sending station (this agn device), rather than whether it was
1427 * received successfully by the destination station.
1429 struct agg_tx_status {
1434 /* refer to ra_tid */
1435 #define IWLAGN_TX_RES_TID_POS 0
1436 #define IWLAGN_TX_RES_TID_MSK 0x0f
1437 #define IWLAGN_TX_RES_RA_POS 4
1438 #define IWLAGN_TX_RES_RA_MSK 0xf0
1440 struct iwlagn_tx_resp {
1441 u8 frame_count; /* 1 no aggregation, >1 aggregation */
1442 u8 bt_kill_count; /* # blocked by bluetooth (unused for agg) */
1443 u8 failure_rts; /* # failures due to unsuccessful RTS */
1444 u8 failure_frame; /* # failures due to no ACK (unused for agg) */
1446 /* For non-agg: Rate at which frame was successful.
1447 * For agg: Rate at which all frames were transmitted. */
1448 __le32 rate_n_flags; /* RATE_MCS_* */
1450 /* For non-agg: RTS + CTS + frame tx attempts time + ACK.
1451 * For agg: RTS + CTS + aggregation tx time + block-ack time. */
1452 __le16 wireless_media_time; /* uSecs */
1454 u8 pa_status; /* RF power amplifier measurement (not used) */
1455 u8 pa_integ_res_a[3];
1456 u8 pa_integ_res_b[3];
1457 u8 pa_integ_res_C[3];
1463 u8 ra_tid; /* tid (0:3), sta_id (4:7) */
1466 * For non-agg: frame status TX_STATUS_*
1467 * For agg: status of 1st frame, AGG_TX_STATE_*; other frame status
1468 * fields follow this one, up to frame_count.
1470 * 11- 0: AGG_TX_STATE_* status code
1471 * 15-12: Retry count for 1st frame in aggregation (retries
1472 * occur if tx failed for this frame when it was a
1473 * member of a previous aggregation block). If rate
1474 * scaling is used, retry count indicates the rate
1475 * table entry used for all frames in the new agg.
1476 * 31-16: Sequence # for this frame's Tx cmd (not SSN!)
1478 struct agg_tx_status status; /* TX status (in aggregation -
1479 * status of 1st frame) */
1482 * REPLY_COMPRESSED_BA = 0xc5 (response only, not a command)
1484 * Reports Block-Acknowledge from recipient station
1486 struct iwl_compressed_ba_resp {
1487 __le32 sta_addr_lo32;
1488 __le16 sta_addr_hi16;
1491 /* Index of recipient (BA-sending) station in uCode's station table */
1498 u8 txed; /* number of frames sent */
1499 u8 txed_2_done; /* number of frames acked */
1504 * REPLY_TX_PWR_TABLE_CMD = 0x97 (command, has simple generic response)
1508 /*RS_NEW_API: only TLC_RTS remains and moved to bit 0 */
1509 #define LINK_QUAL_FLAGS_SET_STA_TLC_RTS_MSK (1 << 0)
1511 /* # of EDCA prioritized tx fifos */
1512 #define LINK_QUAL_AC_NUM AC_NUM
1514 /* # entries in rate scale table to support Tx retries */
1515 #define LINK_QUAL_MAX_RETRY_NUM 16
1517 /* Tx antenna selection values */
1518 #define LINK_QUAL_ANT_A_MSK (1 << 0)
1519 #define LINK_QUAL_ANT_B_MSK (1 << 1)
1520 #define LINK_QUAL_ANT_MSK (LINK_QUAL_ANT_A_MSK|LINK_QUAL_ANT_B_MSK)
1524 * struct iwl_link_qual_general_params
1526 * Used in REPLY_TX_LINK_QUALITY_CMD
1528 struct iwl_link_qual_general_params {
1531 /* No entries at or above this (driver chosen) index contain MIMO */
1534 /* Best single antenna to use for single stream (legacy, SISO). */
1535 u8 single_stream_ant_msk; /* LINK_QUAL_ANT_* */
1537 /* Best antennas to use for MIMO */
1538 u8 dual_stream_ant_msk; /* LINK_QUAL_ANT_* */
1541 * If driver needs to use different initial rates for different
1542 * EDCA QOS access categories (as implemented by tx fifos 0-3),
1543 * this table will set that up, by indicating the indexes in the
1544 * rs_table[LINK_QUAL_MAX_RETRY_NUM] rate table at which to start.
1545 * Otherwise, driver should set all entries to 0.
1548 * 0 = Background, 1 = Best Effort (normal), 2 = Video, 3 = Voice
1549 * TX FIFOs above 3 use same value (typically 0) as TX FIFO 3.
1551 u8 start_rate_index[LINK_QUAL_AC_NUM];
1554 #define LINK_QUAL_AGG_TIME_LIMIT_DEF (4000) /* 4 milliseconds */
1555 #define LINK_QUAL_AGG_TIME_LIMIT_MAX (8000)
1556 #define LINK_QUAL_AGG_TIME_LIMIT_MIN (100)
1558 #define LINK_QUAL_AGG_DISABLE_START_DEF (3)
1559 #define LINK_QUAL_AGG_DISABLE_START_MAX (255)
1560 #define LINK_QUAL_AGG_DISABLE_START_MIN (0)
1562 #define LINK_QUAL_AGG_FRAME_LIMIT_DEF (63)
1563 #define LINK_QUAL_AGG_FRAME_LIMIT_MAX (63)
1564 #define LINK_QUAL_AGG_FRAME_LIMIT_MIN (0)
1567 * struct iwl_link_qual_agg_params
1569 * Used in REPLY_TX_LINK_QUALITY_CMD
1571 struct iwl_link_qual_agg_params {
1574 *Maximum number of uSec in aggregation.
1575 * default set to 4000 (4 milliseconds) if not configured in .cfg
1577 __le16 agg_time_limit;
1580 * Number of Tx retries allowed for a frame, before that frame will
1581 * no longer be considered for the start of an aggregation sequence
1582 * (scheduler will then try to tx it as single frame).
1583 * Driver should set this to 3.
1585 u8 agg_dis_start_th;
1588 * Maximum number of frames in aggregation.
1589 * 0 = no limit (default). 1 = no aggregation.
1590 * Other values = max # frames in aggregation.
1592 u8 agg_frame_cnt_limit;
1598 * REPLY_TX_LINK_QUALITY_CMD = 0x4e (command, has simple generic response)
1602 * Each station in the agn device's internal station table has its own table
1604 * Tx rates and modulation modes (e.g. legacy/SISO/MIMO) for retrying Tx when
1605 * an ACK is not received. This command replaces the entire table for
1608 * NOTE: Station must already be in agn device's station table.
1609 * Use REPLY_ADD_STA.
1611 * The rate scaling procedures described below work well. Of course, other
1612 * procedures are possible, and may work better for particular environments.
1615 * FILLING THE RATE TABLE
1617 * Given a particular initial rate and mode, as determined by the rate
1618 * scaling algorithm described below, the Linux driver uses the following
1619 * formula to fill the rs_table[LINK_QUAL_MAX_RETRY_NUM] rate table in the
1620 * Link Quality command:
1623 * 1) If using High-throughput (HT) (SISO or MIMO) initial rate:
1624 * a) Use this same initial rate for first 3 entries.
1625 * b) Find next lower available rate using same mode (SISO or MIMO),
1626 * use for next 3 entries. If no lower rate available, switch to
1627 * legacy mode (no HT40 channel, no MIMO, no short guard interval).
1628 * c) If using MIMO, set command's mimo_delimiter to number of entries
1629 * using MIMO (3 or 6).
1630 * d) After trying 2 HT rates, switch to legacy mode (no HT40 channel,
1631 * no MIMO, no short guard interval), at the next lower bit rate
1632 * (e.g. if second HT bit rate was 54, try 48 legacy), and follow
1633 * legacy procedure for remaining table entries.
1635 * 2) If using legacy initial rate:
1636 * a) Use the initial rate for only one entry.
1637 * b) For each following entry, reduce the rate to next lower available
1638 * rate, until reaching the lowest available rate.
1639 * c) When reducing rate, also switch antenna selection.
1640 * d) Once lowest available rate is reached, repeat this rate until
1641 * rate table is filled (16 entries), switching antenna each entry.
1644 * ACCUMULATING HISTORY
1646 * The rate scaling algorithm for agn devices, as implemented in Linux driver,
1647 * uses two sets of frame Tx success history: One for the current/active
1648 * modulation mode, and one for a speculative/search mode that is being
1649 * attempted. If the speculative mode turns out to be more effective (i.e.
1650 * actual transfer rate is better), then the driver continues to use the
1651 * speculative mode as the new current active mode.
1653 * Each history set contains, separately for each possible rate, data for a
1654 * sliding window of the 62 most recent tx attempts at that rate. The data
1655 * includes a shifting bitmap of success(1)/failure(0), and sums of successful
1656 * and attempted frames, from which the driver can additionally calculate a
1657 * success ratio (success / attempted) and number of failures
1658 * (attempted - success), and control the size of the window (attempted).
1659 * The driver uses the bit map to remove successes from the success sum, as
1660 * the oldest tx attempts fall out of the window.
1662 * When the agn device makes multiple tx attempts for a given frame, each
1663 * attempt might be at a different rate, and have different modulation
1664 * characteristics (e.g. antenna, fat channel, short guard interval), as set
1665 * up in the rate scaling table in the Link Quality command. The driver must
1666 * determine which rate table entry was used for each tx attempt, to determine
1667 * which rate-specific history to update, and record only those attempts that
1668 * match the modulation characteristics of the history set.
1670 * When using block-ack (aggregation), all frames are transmitted at the same
1671 * rate, since there is no per-attempt acknowledgment from the destination
1672 * station. The Tx response struct iwl_tx_resp indicates the Tx rate in
1673 * rate_n_flags field. After receiving a block-ack, the driver can update
1674 * history for the entire block all at once.
1677 * FINDING BEST STARTING RATE:
1679 * When working with a selected initial modulation mode (see below), the
1680 * driver attempts to find a best initial rate. The initial rate is the
1681 * first entry in the Link Quality command's rate table.
1683 * 1) Calculate actual throughput (success ratio * expected throughput, see
1684 * table below) for current initial rate. Do this only if enough frames
1685 * have been attempted to make the value meaningful: at least 6 failed
1686 * tx attempts, or at least 8 successes. If not enough, don't try rate
1689 * 2) Find available rates adjacent to current initial rate. Available means:
1690 * a) supported by hardware &&
1691 * b) supported by association &&
1692 * c) within any constraints selected by user
1694 * 3) Gather measured throughputs for adjacent rates. These might not have
1695 * enough history to calculate a throughput. That's okay, we might try
1696 * using one of them anyway!
1698 * 4) Try decreasing rate if, for current rate:
1699 * a) success ratio is < 15% ||
1700 * b) lower adjacent rate has better measured throughput ||
1701 * c) higher adjacent rate has worse throughput, and lower is unmeasured
1703 * As a sanity check, if decrease was determined above, leave rate
1705 * a) lower rate unavailable
1706 * b) success ratio at current rate > 85% (very good)
1707 * c) current measured throughput is better than expected throughput
1708 * of lower rate (under perfect 100% tx conditions, see table below)
1710 * 5) Try increasing rate if, for current rate:
1711 * a) success ratio is < 15% ||
1712 * b) both adjacent rates' throughputs are unmeasured (try it!) ||
1713 * b) higher adjacent rate has better measured throughput ||
1714 * c) lower adjacent rate has worse throughput, and higher is unmeasured
1716 * As a sanity check, if increase was determined above, leave rate
1718 * a) success ratio at current rate < 70%. This is not particularly
1719 * good performance; higher rate is sure to have poorer success.
1721 * 6) Re-evaluate the rate after each tx frame. If working with block-
1722 * acknowledge, history and statistics may be calculated for the entire
1723 * block (including prior history that fits within the history windows),
1724 * before re-evaluation.
1726 * FINDING BEST STARTING MODULATION MODE:
1728 * After working with a modulation mode for a "while" (and doing rate scaling),
1729 * the driver searches for a new initial mode in an attempt to improve
1730 * throughput. The "while" is measured by numbers of attempted frames:
1732 * For legacy mode, search for new mode after:
1733 * 480 successful frames, or 160 failed frames
1734 * For high-throughput modes (SISO or MIMO), search for new mode after:
1735 * 4500 successful frames, or 400 failed frames
1737 * Mode switch possibilities are (3 for each mode):
1740 * Change antenna, try SISO (if HT association), try MIMO (if HT association)
1742 * Change antenna, try MIMO, try shortened guard interval (SGI)
1744 * Try SISO antenna A, SISO antenna B, try shortened guard interval (SGI)
1746 * When trying a new mode, use the same bit rate as the old/current mode when
1747 * trying antenna switches and shortened guard interval. When switching to
1748 * SISO from MIMO or legacy, or to MIMO from SISO or legacy, use a rate
1749 * for which the expected throughput (under perfect conditions) is about the
1750 * same or slightly better than the actual measured throughput delivered by
1751 * the old/current mode.
1753 * Actual throughput can be estimated by multiplying the expected throughput
1754 * by the success ratio (successful / attempted tx frames). Frame size is
1755 * not considered in this calculation; it assumes that frame size will average
1756 * out to be fairly consistent over several samples. The following are
1757 * metric values for expected throughput assuming 100% success ratio.
1758 * Only G band has support for CCK rates:
1760 * RATE: 1 2 5 11 6 9 12 18 24 36 48 54 60
1762 * G: 7 13 35 58 40 57 72 98 121 154 177 186 186
1763 * A: 0 0 0 0 40 57 72 98 121 154 177 186 186
1764 * SISO 20MHz: 0 0 0 0 42 42 76 102 124 159 183 193 202
1765 * SGI SISO 20MHz: 0 0 0 0 46 46 82 110 132 168 192 202 211
1766 * MIMO 20MHz: 0 0 0 0 74 74 123 155 179 214 236 244 251
1767 * SGI MIMO 20MHz: 0 0 0 0 81 81 131 164 188 222 243 251 257
1768 * SISO 40MHz: 0 0 0 0 77 77 127 160 184 220 242 250 257
1769 * SGI SISO 40MHz: 0 0 0 0 83 83 135 169 193 229 250 257 264
1770 * MIMO 40MHz: 0 0 0 0 123 123 182 214 235 264 279 285 289
1771 * SGI MIMO 40MHz: 0 0 0 0 131 131 191 222 242 270 284 289 293
1773 * After the new mode has been tried for a short while (minimum of 6 failed
1774 * frames or 8 successful frames), compare success ratio and actual throughput
1775 * estimate of the new mode with the old. If either is better with the new
1776 * mode, continue to use the new mode.
1778 * Continue comparing modes until all 3 possibilities have been tried.
1779 * If moving from legacy to HT, try all 3 possibilities from the new HT
1780 * mode. After trying all 3, a best mode is found. Continue to use this mode
1781 * for the longer "while" described above (e.g. 480 successful frames for
1782 * legacy), and then repeat the search process.
1785 struct iwl_link_quality_cmd {
1787 /* Index of destination/recipient station in uCode's station table */
1790 __le16 control; /* not used */
1791 struct iwl_link_qual_general_params general_params;
1792 struct iwl_link_qual_agg_params agg_params;
1795 * Rate info; when using rate-scaling, Tx command's initial_rate_index
1796 * specifies 1st Tx rate attempted, via index into this table.
1797 * agn devices works its way through table when retrying Tx.
1800 __le32 rate_n_flags; /* RATE_MCS_*, IWL_RATE_* */
1801 } rs_table[LINK_QUAL_MAX_RETRY_NUM];
1806 * BT configuration enable flags:
1807 * bit 0 - 1: BT channel announcement enabled
1809 * bit 1 - 1: priority of BT device enabled
1811 * bit 2 - 1: BT 2 wire support enabled
1814 #define BT_COEX_DISABLE (0x0)
1815 #define BT_ENABLE_CHANNEL_ANNOUNCE BIT(0)
1816 #define BT_ENABLE_PRIORITY BIT(1)
1817 #define BT_ENABLE_2_WIRE BIT(2)
1819 #define BT_COEX_DISABLE (0x0)
1820 #define BT_COEX_ENABLE (BT_ENABLE_CHANNEL_ANNOUNCE | BT_ENABLE_PRIORITY)
1822 #define BT_LEAD_TIME_MIN (0x0)
1823 #define BT_LEAD_TIME_DEF (0x1E)
1824 #define BT_LEAD_TIME_MAX (0xFF)
1826 #define BT_MAX_KILL_MIN (0x1)
1827 #define BT_MAX_KILL_DEF (0x5)
1828 #define BT_MAX_KILL_MAX (0xFF)
1830 #define BT_DURATION_LIMIT_DEF 625
1831 #define BT_DURATION_LIMIT_MAX 1250
1832 #define BT_DURATION_LIMIT_MIN 625
1834 #define BT_ON_THRESHOLD_DEF 4
1835 #define BT_ON_THRESHOLD_MAX 1000
1836 #define BT_ON_THRESHOLD_MIN 1
1838 #define BT_FRAG_THRESHOLD_DEF 0
1839 #define BT_FRAG_THRESHOLD_MAX 0
1840 #define BT_FRAG_THRESHOLD_MIN 0
1842 #define BT_AGG_THRESHOLD_DEF 1200
1843 #define BT_AGG_THRESHOLD_MAX 8000
1844 #define BT_AGG_THRESHOLD_MIN 400
1847 * REPLY_BT_CONFIG = 0x9b (command, has simple generic response)
1849 * agn devices support hardware handshake with Bluetooth device on
1850 * same platform. Bluetooth device alerts wireless device when it will Tx;
1851 * wireless device can delay or kill its own Tx to accommodate.
1858 __le32 kill_ack_mask;
1859 __le32 kill_cts_mask;
1862 #define IWLAGN_BT_FLAG_CHANNEL_INHIBITION BIT(0)
1864 #define IWLAGN_BT_FLAG_COEX_MODE_MASK (BIT(3)|BIT(4)|BIT(5))
1865 #define IWLAGN_BT_FLAG_COEX_MODE_SHIFT 3
1866 #define IWLAGN_BT_FLAG_COEX_MODE_DISABLED 0
1867 #define IWLAGN_BT_FLAG_COEX_MODE_LEGACY_2W 1
1868 #define IWLAGN_BT_FLAG_COEX_MODE_3W 2
1869 #define IWLAGN_BT_FLAG_COEX_MODE_4W 3
1871 #define IWLAGN_BT_FLAG_UCODE_DEFAULT BIT(6)
1872 /* Disable Sync PSPoll on SCO/eSCO */
1873 #define IWLAGN_BT_FLAG_SYNC_2_BT_DISABLE BIT(7)
1875 #define IWLAGN_BT_PSP_MIN_RSSI_THRESHOLD -75 /* dBm */
1876 #define IWLAGN_BT_PSP_MAX_RSSI_THRESHOLD -65 /* dBm */
1878 #define IWLAGN_BT_PRIO_BOOST_MAX 0xFF
1879 #define IWLAGN_BT_PRIO_BOOST_MIN 0x00
1880 #define IWLAGN_BT_PRIO_BOOST_DEFAULT 0xF0
1881 #define IWLAGN_BT_PRIO_BOOST_DEFAULT32 0xF0F0F0F0
1883 #define IWLAGN_BT_MAX_KILL_DEFAULT 5
1885 #define IWLAGN_BT3_T7_DEFAULT 1
1887 enum iwl_bt_kill_idx {
1888 IWL_BT_KILL_DEFAULT = 0,
1889 IWL_BT_KILL_OVERRIDE = 1,
1890 IWL_BT_KILL_REDUCE = 2,
1893 #define IWLAGN_BT_KILL_ACK_MASK_DEFAULT cpu_to_le32(0xffff0000)
1894 #define IWLAGN_BT_KILL_CTS_MASK_DEFAULT cpu_to_le32(0xffff0000)
1895 #define IWLAGN_BT_KILL_ACK_CTS_MASK_SCO cpu_to_le32(0xffffffff)
1896 #define IWLAGN_BT_KILL_ACK_CTS_MASK_REDUCE cpu_to_le32(0)
1898 #define IWLAGN_BT3_PRIO_SAMPLE_DEFAULT 2
1900 #define IWLAGN_BT3_T2_DEFAULT 0xc
1902 #define IWLAGN_BT_VALID_ENABLE_FLAGS cpu_to_le16(BIT(0))
1903 #define IWLAGN_BT_VALID_BOOST cpu_to_le16(BIT(1))
1904 #define IWLAGN_BT_VALID_MAX_KILL cpu_to_le16(BIT(2))
1905 #define IWLAGN_BT_VALID_3W_TIMERS cpu_to_le16(BIT(3))
1906 #define IWLAGN_BT_VALID_KILL_ACK_MASK cpu_to_le16(BIT(4))
1907 #define IWLAGN_BT_VALID_KILL_CTS_MASK cpu_to_le16(BIT(5))
1908 #define IWLAGN_BT_VALID_REDUCED_TX_PWR cpu_to_le16(BIT(6))
1909 #define IWLAGN_BT_VALID_3W_LUT cpu_to_le16(BIT(7))
1911 #define IWLAGN_BT_ALL_VALID_MSK (IWLAGN_BT_VALID_ENABLE_FLAGS | \
1912 IWLAGN_BT_VALID_BOOST | \
1913 IWLAGN_BT_VALID_MAX_KILL | \
1914 IWLAGN_BT_VALID_3W_TIMERS | \
1915 IWLAGN_BT_VALID_KILL_ACK_MASK | \
1916 IWLAGN_BT_VALID_KILL_CTS_MASK | \
1917 IWLAGN_BT_VALID_REDUCED_TX_PWR | \
1918 IWLAGN_BT_VALID_3W_LUT)
1920 #define IWLAGN_BT_REDUCED_TX_PWR BIT(0)
1922 #define IWLAGN_BT_DECISION_LUT_SIZE 12
1924 struct iwl_basic_bt_cmd {
1926 u8 ledtime; /* unused */
1928 u8 bt3_timer_t7_value;
1929 __le32 kill_ack_mask;
1930 __le32 kill_cts_mask;
1931 u8 bt3_prio_sample_time;
1932 u8 bt3_timer_t2_value;
1933 __le16 bt4_reaction_time; /* unused */
1934 __le32 bt3_lookup_table[IWLAGN_BT_DECISION_LUT_SIZE];
1936 * bit 0: use reduced tx power for control frame
1937 * bit 1 - 7: reserved
1944 struct iwl_bt_cmd_v1 {
1945 struct iwl_basic_bt_cmd basic;
1948 * set IWLAGN_BT_VALID_BOOST to "1" in "valid" bitmask
1949 * if configure the following patterns
1951 u8 tx_prio_boost; /* SW boost of WiFi tx priority */
1952 __le16 rx_prio_boost; /* SW boost of WiFi rx priority */
1955 struct iwl_bt_cmd_v2 {
1956 struct iwl_basic_bt_cmd basic;
1959 * set IWLAGN_BT_VALID_BOOST to "1" in "valid" bitmask
1960 * if configure the following patterns
1963 u8 tx_prio_boost; /* SW boost of WiFi tx priority */
1964 __le16 rx_prio_boost; /* SW boost of WiFi rx priority */
1967 #define IWLAGN_BT_SCO_ACTIVE cpu_to_le32(BIT(0))
1969 struct iwlagn_bt_sco_cmd {
1973 /******************************************************************************
1975 * Spectrum Management (802.11h) Commands, Responses, Notifications:
1977 *****************************************************************************/
1980 * Spectrum Management
1982 #define MEASUREMENT_FILTER_FLAG (RXON_FILTER_PROMISC_MSK | \
1983 RXON_FILTER_CTL2HOST_MSK | \
1984 RXON_FILTER_ACCEPT_GRP_MSK | \
1985 RXON_FILTER_DIS_DECRYPT_MSK | \
1986 RXON_FILTER_DIS_GRP_DECRYPT_MSK | \
1987 RXON_FILTER_ASSOC_MSK | \
1988 RXON_FILTER_BCON_AWARE_MSK)
1990 struct iwl_measure_channel {
1991 __le32 duration; /* measurement duration in extended beacon
1993 u8 channel; /* channel to measure */
1994 u8 type; /* see enum iwl_measure_type */
1999 * REPLY_SPECTRUM_MEASUREMENT_CMD = 0x74 (command)
2001 struct iwl_spectrum_cmd {
2002 __le16 len; /* number of bytes starting from token */
2003 u8 token; /* token id */
2004 u8 id; /* measurement id -- 0 or 1 */
2005 u8 origin; /* 0 = TGh, 1 = other, 2 = TGk */
2006 u8 periodic; /* 1 = periodic */
2007 __le16 path_loss_timeout;
2008 __le32 start_time; /* start time in extended beacon format */
2010 __le32 flags; /* rxon flags */
2011 __le32 filter_flags; /* rxon filter flags */
2012 __le16 channel_count; /* minimum 1, maximum 10 */
2014 struct iwl_measure_channel channels[10];
2018 * REPLY_SPECTRUM_MEASUREMENT_CMD = 0x74 (response)
2020 struct iwl_spectrum_resp {
2022 u8 id; /* id of the prior command replaced, or 0xff */
2023 __le16 status; /* 0 - command will be handled
2024 * 1 - cannot handle (conflicts with another
2028 enum iwl_measurement_state {
2029 IWL_MEASUREMENT_START = 0,
2030 IWL_MEASUREMENT_STOP = 1,
2033 enum iwl_measurement_status {
2034 IWL_MEASUREMENT_OK = 0,
2035 IWL_MEASUREMENT_CONCURRENT = 1,
2036 IWL_MEASUREMENT_CSA_CONFLICT = 2,
2037 IWL_MEASUREMENT_TGH_CONFLICT = 3,
2039 IWL_MEASUREMENT_STOPPED = 6,
2040 IWL_MEASUREMENT_TIMEOUT = 7,
2041 IWL_MEASUREMENT_PERIODIC_FAILED = 8,
2044 #define NUM_ELEMENTS_IN_HISTOGRAM 8
2046 struct iwl_measurement_histogram {
2047 __le32 ofdm[NUM_ELEMENTS_IN_HISTOGRAM]; /* in 0.8usec counts */
2048 __le32 cck[NUM_ELEMENTS_IN_HISTOGRAM]; /* in 1usec counts */
2051 /* clear channel availability counters */
2052 struct iwl_measurement_cca_counters {
2057 enum iwl_measure_type {
2058 IWL_MEASURE_BASIC = (1 << 0),
2059 IWL_MEASURE_CHANNEL_LOAD = (1 << 1),
2060 IWL_MEASURE_HISTOGRAM_RPI = (1 << 2),
2061 IWL_MEASURE_HISTOGRAM_NOISE = (1 << 3),
2062 IWL_MEASURE_FRAME = (1 << 4),
2063 /* bits 5:6 are reserved */
2064 IWL_MEASURE_IDLE = (1 << 7),
2068 * SPECTRUM_MEASURE_NOTIFICATION = 0x75 (notification only, not a command)
2070 struct iwl_spectrum_notification {
2071 u8 id; /* measurement id -- 0 or 1 */
2073 u8 channel_index; /* index in measurement channel list */
2074 u8 state; /* 0 - start, 1 - stop */
2075 __le32 start_time; /* lower 32-bits of TSF */
2076 u8 band; /* 0 - 5.2GHz, 1 - 2.4GHz */
2078 u8 type; /* see enum iwl_measurement_type */
2080 /* NOTE: cca_ofdm, cca_cck, basic_type, and histogram are only only
2081 * valid if applicable for measurement type requested. */
2082 __le32 cca_ofdm; /* cca fraction time in 40Mhz clock periods */
2083 __le32 cca_cck; /* cca fraction time in 44Mhz clock periods */
2084 __le32 cca_time; /* channel load time in usecs */
2085 u8 basic_type; /* 0 - bss, 1 - ofdm preamble, 2 -
2088 struct iwl_measurement_histogram histogram;
2089 __le32 stop_time; /* lower 32-bits of TSF */
2090 __le32 status; /* see iwl_measurement_status */
2093 /******************************************************************************
2095 * Power Management Commands, Responses, Notifications:
2097 *****************************************************************************/
2100 * struct iwl_powertable_cmd - Power Table Command
2101 * @flags: See below:
2103 * POWER_TABLE_CMD = 0x77 (command, has simple generic response)
2106 * bit 0 - '0' Driver not allow power management
2107 * '1' Driver allow PM (use rest of parameters)
2109 * uCode send sleep notifications:
2110 * bit 1 - '0' Don't send sleep notification
2111 * '1' send sleep notification (SEND_PM_NOTIFICATION)
2114 * bit 2 - '0' PM have to walk up every DTIM
2115 * '1' PM could sleep over DTIM till listen Interval.
2118 * bit 3 - '0' (PCI_CFG_LINK_CTRL & 0x1)
2119 * '1' !(PCI_CFG_LINK_CTRL & 0x1)
2122 * bit 4 - '1' Put radio to sleep when receiving frame for others
2125 * bit 31/30- '00' use both mac/xtal sleeps
2126 * '01' force Mac sleep
2127 * '10' force xtal sleep
2130 * NOTE: if sleep_interval[SLEEP_INTRVL_TABLE_SIZE-1] > DTIM period then
2131 * ucode assume sleep over DTIM is allowed and we don't need to wake up
2134 #define IWL_POWER_VEC_SIZE 5
2136 #define IWL_POWER_DRIVER_ALLOW_SLEEP_MSK cpu_to_le16(BIT(0))
2137 #define IWL_POWER_POWER_SAVE_ENA_MSK cpu_to_le16(BIT(0))
2138 #define IWL_POWER_POWER_MANAGEMENT_ENA_MSK cpu_to_le16(BIT(1))
2139 #define IWL_POWER_SLEEP_OVER_DTIM_MSK cpu_to_le16(BIT(2))
2140 #define IWL_POWER_PCI_PM_MSK cpu_to_le16(BIT(3))
2141 #define IWL_POWER_FAST_PD cpu_to_le16(BIT(4))
2142 #define IWL_POWER_BEACON_FILTERING cpu_to_le16(BIT(5))
2143 #define IWL_POWER_SHADOW_REG_ENA cpu_to_le16(BIT(6))
2144 #define IWL_POWER_CT_KILL_SET cpu_to_le16(BIT(7))
2145 #define IWL_POWER_BT_SCO_ENA cpu_to_le16(BIT(8))
2146 #define IWL_POWER_ADVANCE_PM_ENA_MSK cpu_to_le16(BIT(9))
2148 struct iwl_powertable_cmd {
2150 u8 keep_alive_seconds;
2152 __le32 rx_data_timeout;
2153 __le32 tx_data_timeout;
2154 __le32 sleep_interval[IWL_POWER_VEC_SIZE];
2155 __le32 keep_alive_beacons;
2159 * PM_SLEEP_NOTIFICATION = 0x7A (notification only, not a command)
2160 * all devices identical.
2162 struct iwl_sleep_notification {
2171 /* Sleep states. all devices identical. */
2173 IWL_PM_NO_SLEEP = 0,
2175 IWL_PM_SLP_FULL_MAC_UNASSOCIATE = 2,
2176 IWL_PM_SLP_FULL_MAC_CARD_STATE = 3,
2178 IWL_PM_SLP_REPENT = 5,
2179 IWL_PM_WAKEUP_BY_TIMER = 6,
2180 IWL_PM_WAKEUP_BY_DRIVER = 7,
2181 IWL_PM_WAKEUP_BY_RFKILL = 8,
2183 IWL_PM_NUM_OF_MODES = 12,
2187 * REPLY_CARD_STATE_CMD = 0xa0 (command, has simple generic response)
2189 #define CARD_STATE_CMD_DISABLE 0x00 /* Put card to sleep */
2190 #define CARD_STATE_CMD_ENABLE 0x01 /* Wake up card */
2191 #define CARD_STATE_CMD_HALT 0x02 /* Power down permanently */
2192 struct iwl_card_state_cmd {
2193 __le32 status; /* CARD_STATE_CMD_* request new power state */
2197 * CARD_STATE_NOTIFICATION = 0xa1 (notification only, not a command)
2199 struct iwl_card_state_notif {
2203 #define HW_CARD_DISABLED 0x01
2204 #define SW_CARD_DISABLED 0x02
2205 #define CT_CARD_DISABLED 0x04
2206 #define RXON_CARD_DISABLED 0x10
2208 struct iwl_ct_kill_config {
2210 __le32 critical_temperature_M;
2211 __le32 critical_temperature_R;
2214 /* 1000, and 6x00 */
2215 struct iwl_ct_kill_throttling_config {
2216 __le32 critical_temperature_exit;
2218 __le32 critical_temperature_enter;
2221 /******************************************************************************
2223 * Scan Commands, Responses, Notifications:
2225 *****************************************************************************/
2227 #define SCAN_CHANNEL_TYPE_PASSIVE cpu_to_le32(0)
2228 #define SCAN_CHANNEL_TYPE_ACTIVE cpu_to_le32(1)
2231 * struct iwl_scan_channel - entry in REPLY_SCAN_CMD channel table
2233 * One for each channel in the scan list.
2234 * Each channel can independently select:
2235 * 1) SSID for directed active scans
2236 * 2) Txpower setting (for rate specified within Tx command)
2237 * 3) How long to stay on-channel (behavior may be modified by quiet_time,
2238 * quiet_plcp_th, good_CRC_th)
2240 * To avoid uCode errors, make sure the following are true (see comments
2241 * under struct iwl_scan_cmd about max_out_time and quiet_time):
2242 * 1) If using passive_dwell (i.e. passive_dwell != 0):
2243 * active_dwell <= passive_dwell (< max_out_time if max_out_time != 0)
2244 * 2) quiet_time <= active_dwell
2245 * 3) If restricting off-channel time (i.e. max_out_time !=0):
2246 * passive_dwell < max_out_time
2247 * active_dwell < max_out_time
2250 struct iwl_scan_channel {
2252 * type is defined as:
2253 * 0:0 1 = active, 0 = passive
2254 * 1:20 SSID direct bit map; if a bit is set, then corresponding
2255 * SSID IE is transmitted in probe request.
2259 __le16 channel; /* band is selected by iwl_scan_cmd "flags" field */
2260 u8 tx_gain; /* gain for analog radio */
2261 u8 dsp_atten; /* gain for DSP */
2262 __le16 active_dwell; /* in 1024-uSec TU (time units), typ 5-50 */
2263 __le16 passive_dwell; /* in 1024-uSec TU (time units), typ 20-500 */
2266 /* set number of direct probes __le32 type */
2267 #define IWL_SCAN_PROBE_MASK(n) cpu_to_le32((BIT(n) | (BIT(n) - BIT(1))))
2270 * struct iwl_ssid_ie - directed scan network information element
2272 * Up to 20 of these may appear in REPLY_SCAN_CMD,
2273 * selected by "type" bit field in struct iwl_scan_channel;
2274 * each channel may select different ssids from among the 20 entries.
2275 * SSID IEs get transmitted in reverse order of entry.
2277 struct iwl_ssid_ie {
2283 #define PROBE_OPTION_MAX 20
2284 #define TX_CMD_LIFE_TIME_INFINITE cpu_to_le32(0xFFFFFFFF)
2285 #define IWL_GOOD_CRC_TH_DISABLED 0
2286 #define IWL_GOOD_CRC_TH_DEFAULT cpu_to_le16(1)
2287 #define IWL_GOOD_CRC_TH_NEVER cpu_to_le16(0xffff)
2288 #define IWL_MAX_CMD_SIZE 4096
2291 * REPLY_SCAN_CMD = 0x80 (command)
2293 * The hardware scan command is very powerful; the driver can set it up to
2294 * maintain (relatively) normal network traffic while doing a scan in the
2295 * background. The max_out_time and suspend_time control the ratio of how
2296 * long the device stays on an associated network channel ("service channel")
2297 * vs. how long it's away from the service channel, i.e. tuned to other channels
2300 * max_out_time is the max time off-channel (in usec), and suspend_time
2301 * is how long (in "extended beacon" format) that the scan is "suspended"
2302 * after returning to the service channel. That is, suspend_time is the
2303 * time that we stay on the service channel, doing normal work, between
2304 * scan segments. The driver may set these parameters differently to support
2305 * scanning when associated vs. not associated, and light vs. heavy traffic
2306 * loads when associated.
2308 * After receiving this command, the device's scan engine does the following;
2310 * 1) Sends SCAN_START notification to driver
2311 * 2) Checks to see if it has time to do scan for one channel
2312 * 3) Sends NULL packet, with power-save (PS) bit set to 1,
2313 * to tell AP that we're going off-channel
2314 * 4) Tunes to first channel in scan list, does active or passive scan
2315 * 5) Sends SCAN_RESULT notification to driver
2316 * 6) Checks to see if it has time to do scan on *next* channel in list
2317 * 7) Repeats 4-6 until it no longer has time to scan the next channel
2318 * before max_out_time expires
2319 * 8) Returns to service channel
2320 * 9) Sends NULL packet with PS=0 to tell AP that we're back
2321 * 10) Stays on service channel until suspend_time expires
2322 * 11) Repeats entire process 2-10 until list is complete
2323 * 12) Sends SCAN_COMPLETE notification
2325 * For fast, efficient scans, the scan command also has support for staying on
2326 * a channel for just a short time, if doing active scanning and getting no
2327 * responses to the transmitted probe request. This time is controlled by
2328 * quiet_time, and the number of received packets below which a channel is
2329 * considered "quiet" is controlled by quiet_plcp_threshold.
2331 * For active scanning on channels that have regulatory restrictions against
2332 * blindly transmitting, the scan can listen before transmitting, to make sure
2333 * that there is already legitimate activity on the channel. If enough
2334 * packets are cleanly received on the channel (controlled by good_CRC_th,
2335 * typical value 1), the scan engine starts transmitting probe requests.
2337 * Driver must use separate scan commands for 2.4 vs. 5 GHz bands.
2339 * To avoid uCode errors, see timing restrictions described under
2340 * struct iwl_scan_channel.
2343 enum iwl_scan_flags {
2344 /* BIT(0) currently unused */
2345 IWL_SCAN_FLAGS_ACTION_FRAME_TX = BIT(1),
2346 /* bits 2-7 reserved */
2349 struct iwl_scan_cmd {
2351 u8 scan_flags; /* scan flags: see enum iwl_scan_flags */
2352 u8 channel_count; /* # channels in channel list */
2353 __le16 quiet_time; /* dwell only this # millisecs on quiet channel
2354 * (only for active scan) */
2355 __le16 quiet_plcp_th; /* quiet chnl is < this # pkts (typ. 1) */
2356 __le16 good_CRC_th; /* passive -> active promotion threshold */
2357 __le16 rx_chain; /* RXON_RX_CHAIN_* */
2358 __le32 max_out_time; /* max usec to be away from associated (service)
2360 __le32 suspend_time; /* pause scan this long (in "extended beacon
2361 * format") when returning to service chnl:
2363 __le32 flags; /* RXON_FLG_* */
2364 __le32 filter_flags; /* RXON_FILTER_* */
2366 /* For active scans (set to all-0s for passive scans).
2367 * Does not include payload. Must specify Tx rate; no rate scaling. */
2368 struct iwl_tx_cmd tx_cmd;
2370 /* For directed active scans (set to all-0s otherwise) */
2371 struct iwl_ssid_ie direct_scan[PROBE_OPTION_MAX];
2374 * Probe request frame, followed by channel list.
2376 * Size of probe request frame is specified by byte count in tx_cmd.
2377 * Channel list follows immediately after probe request frame.
2378 * Number of channels in list is specified by channel_count.
2379 * Each channel in list is of type:
2381 * struct iwl_scan_channel channels[0];
2383 * NOTE: Only one band of channels can be scanned per pass. You
2384 * must not mix 2.4GHz channels and 5.2GHz channels, and you must wait
2385 * for one scan to complete (i.e. receive SCAN_COMPLETE_NOTIFICATION)
2386 * before requesting another scan.
2391 /* Can abort will notify by complete notification with abort status. */
2392 #define CAN_ABORT_STATUS cpu_to_le32(0x1)
2393 /* complete notification statuses */
2394 #define ABORT_STATUS 0x2
2397 * REPLY_SCAN_CMD = 0x80 (response)
2399 struct iwl_scanreq_notification {
2400 __le32 status; /* 1: okay, 2: cannot fulfill request */
2404 * SCAN_START_NOTIFICATION = 0x82 (notification only, not a command)
2406 struct iwl_scanstart_notification {
2409 __le32 beacon_timer;
2416 #define SCAN_OWNER_STATUS 0x1
2417 #define MEASURE_OWNER_STATUS 0x2
2419 #define IWL_PROBE_STATUS_OK 0
2420 #define IWL_PROBE_STATUS_TX_FAILED BIT(0)
2421 /* error statuses combined with TX_FAILED */
2422 #define IWL_PROBE_STATUS_FAIL_TTL BIT(1)
2423 #define IWL_PROBE_STATUS_FAIL_BT BIT(2)
2425 #define NUMBER_OF_STATISTICS 1 /* first __le32 is good CRC */
2427 * SCAN_RESULTS_NOTIFICATION = 0x83 (notification only, not a command)
2429 struct iwl_scanresults_notification {
2433 u8 num_probe_not_sent; /* not enough time to send */
2436 __le32 statistics[NUMBER_OF_STATISTICS];
2440 * SCAN_COMPLETE_NOTIFICATION = 0x84 (notification only, not a command)
2442 struct iwl_scancomplete_notification {
2443 u8 scanned_channels;
2445 u8 bt_status; /* BT On/Off status */
2452 /******************************************************************************
2454 * IBSS/AP Commands and Notifications:
2456 *****************************************************************************/
2458 enum iwl_ibss_manager {
2459 IWL_NOT_IBSS_MANAGER = 0,
2460 IWL_IBSS_MANAGER = 1,
2464 * BEACON_NOTIFICATION = 0x90 (notification only, not a command)
2467 struct iwlagn_beacon_notif {
2468 struct iwlagn_tx_resp beacon_notify_hdr;
2471 __le32 ibss_mgr_status;
2475 * REPLY_TX_BEACON = 0x91 (command, has simple generic response)
2478 struct iwl_tx_beacon_cmd {
2479 struct iwl_tx_cmd tx;
2483 struct ieee80211_hdr frame[0]; /* beacon frame */
2486 /******************************************************************************
2488 * Statistics Commands and Notifications:
2490 *****************************************************************************/
2492 #define IWL_TEMP_CONVERT 260
2494 #define SUP_RATE_11A_MAX_NUM_CHANNELS 8
2495 #define SUP_RATE_11B_MAX_NUM_CHANNELS 4
2496 #define SUP_RATE_11G_MAX_NUM_CHANNELS 12
2498 /* Used for passing to driver number of successes and failures per rate */
2499 struct rate_histogram {
2501 __le32 a[SUP_RATE_11A_MAX_NUM_CHANNELS];
2502 __le32 b[SUP_RATE_11B_MAX_NUM_CHANNELS];
2503 __le32 g[SUP_RATE_11G_MAX_NUM_CHANNELS];
2506 __le32 a[SUP_RATE_11A_MAX_NUM_CHANNELS];
2507 __le32 b[SUP_RATE_11B_MAX_NUM_CHANNELS];
2508 __le32 g[SUP_RATE_11G_MAX_NUM_CHANNELS];
2512 /* statistics command response */
2514 struct statistics_dbg {
2517 __le32 wait_for_silence_timeout_cnt;
2521 struct statistics_rx_phy {
2527 __le32 early_overrun_err;
2529 __le32 false_alarm_cnt;
2530 __le32 fina_sync_err_cnt;
2532 __le32 fina_timeout;
2533 __le32 unresponded_rts;
2534 __le32 rxe_frame_limit_overrun;
2535 __le32 sent_ack_cnt;
2536 __le32 sent_cts_cnt;
2537 __le32 sent_ba_rsp_cnt;
2538 __le32 dsp_self_kill;
2539 __le32 mh_format_err;
2540 __le32 re_acq_main_rssi_sum;
2544 struct statistics_rx_ht_phy {
2547 __le32 early_overrun_err;
2550 __le32 mh_format_err;
2551 __le32 agg_crc32_good;
2552 __le32 agg_mpdu_cnt;
2554 __le32 unsupport_mcs;
2557 #define INTERFERENCE_DATA_AVAILABLE cpu_to_le32(1)
2559 struct statistics_rx_non_phy {
2560 __le32 bogus_cts; /* CTS received when not expecting CTS */
2561 __le32 bogus_ack; /* ACK received when not expecting ACK */
2562 __le32 non_bssid_frames; /* number of frames with BSSID that
2563 * doesn't belong to the STA BSSID */
2564 __le32 filtered_frames; /* count frames that were dumped in the
2565 * filtering process */
2566 __le32 non_channel_beacons; /* beacons with our bss id but not on
2567 * our serving channel */
2568 __le32 channel_beacons; /* beacons with our bss id and in our
2569 * serving channel */
2570 __le32 num_missed_bcon; /* number of missed beacons */
2571 __le32 adc_rx_saturation_time; /* count in 0.8us units the time the
2572 * ADC was in saturation */
2573 __le32 ina_detection_search_time;/* total time (in 0.8us) searched
2575 __le32 beacon_silence_rssi_a; /* RSSI silence after beacon frame */
2576 __le32 beacon_silence_rssi_b; /* RSSI silence after beacon frame */
2577 __le32 beacon_silence_rssi_c; /* RSSI silence after beacon frame */
2578 __le32 interference_data_flag; /* flag for interference data
2579 * availability. 1 when data is
2581 __le32 channel_load; /* counts RX Enable time in uSec */
2582 __le32 dsp_false_alarms; /* DSP false alarm (both OFDM
2583 * and CCK) counter */
2584 __le32 beacon_rssi_a;
2585 __le32 beacon_rssi_b;
2586 __le32 beacon_rssi_c;
2587 __le32 beacon_energy_a;
2588 __le32 beacon_energy_b;
2589 __le32 beacon_energy_c;
2592 struct statistics_rx_non_phy_bt {
2593 struct statistics_rx_non_phy common;
2594 /* additional stats for bt */
2595 __le32 num_bt_kills;
2599 struct statistics_rx {
2600 struct statistics_rx_phy ofdm;
2601 struct statistics_rx_phy cck;
2602 struct statistics_rx_non_phy general;
2603 struct statistics_rx_ht_phy ofdm_ht;
2606 struct statistics_rx_bt {
2607 struct statistics_rx_phy ofdm;
2608 struct statistics_rx_phy cck;
2609 struct statistics_rx_non_phy_bt general;
2610 struct statistics_rx_ht_phy ofdm_ht;
2614 * struct statistics_tx_power - current tx power
2616 * @ant_a: current tx power on chain a in 1/2 dB step
2617 * @ant_b: current tx power on chain b in 1/2 dB step
2618 * @ant_c: current tx power on chain c in 1/2 dB step
2620 struct statistics_tx_power {
2627 struct statistics_tx_non_phy_agg {
2629 __le32 ba_reschedule_frames;
2630 __le32 scd_query_agg_frame_cnt;
2631 __le32 scd_query_no_agg;
2632 __le32 scd_query_agg;
2633 __le32 scd_query_mismatch;
2634 __le32 frame_not_ready;
2636 __le32 bt_prio_kill;
2637 __le32 rx_ba_rsp_cnt;
2640 struct statistics_tx {
2641 __le32 preamble_cnt;
2642 __le32 rx_detected_cnt;
2643 __le32 bt_prio_defer_cnt;
2644 __le32 bt_prio_kill_cnt;
2645 __le32 few_bytes_cnt;
2648 __le32 expected_ack_cnt;
2649 __le32 actual_ack_cnt;
2650 __le32 dump_msdu_cnt;
2651 __le32 burst_abort_next_frame_mismatch_cnt;
2652 __le32 burst_abort_missing_next_frame_cnt;
2653 __le32 cts_timeout_collision;
2654 __le32 ack_or_ba_timeout_collision;
2655 struct statistics_tx_non_phy_agg agg;
2657 * "tx_power" are optional parameters provided by uCode,
2658 * 6000 series is the only device provide the information,
2659 * Those are reserved fields for all the other devices
2661 struct statistics_tx_power tx_power;
2666 struct statistics_div {
2675 struct statistics_general_common {
2676 __le32 temperature; /* radio temperature */
2677 __le32 temperature_m; /* radio voltage */
2678 struct statistics_dbg dbg;
2682 __le32 ttl_timestamp;
2683 struct statistics_div div;
2684 __le32 rx_enable_counter;
2686 * num_of_sos_states:
2687 * count the number of times we have to re-tune
2688 * in order to get out of bad PHY status
2690 __le32 num_of_sos_states;
2693 struct statistics_bt_activity {
2695 __le32 hi_priority_tx_req_cnt;
2696 __le32 hi_priority_tx_denied_cnt;
2697 __le32 lo_priority_tx_req_cnt;
2698 __le32 lo_priority_tx_denied_cnt;
2700 __le32 hi_priority_rx_req_cnt;
2701 __le32 hi_priority_rx_denied_cnt;
2702 __le32 lo_priority_rx_req_cnt;
2703 __le32 lo_priority_rx_denied_cnt;
2706 struct statistics_general {
2707 struct statistics_general_common common;
2712 struct statistics_general_bt {
2713 struct statistics_general_common common;
2714 struct statistics_bt_activity activity;
2719 #define UCODE_STATISTICS_CLEAR_MSK (0x1 << 0)
2720 #define UCODE_STATISTICS_FREQUENCY_MSK (0x1 << 1)
2721 #define UCODE_STATISTICS_NARROW_BAND_MSK (0x1 << 2)
2724 * REPLY_STATISTICS_CMD = 0x9c,
2725 * all devices identical.
2727 * This command triggers an immediate response containing uCode statistics.
2728 * The response is in the same format as STATISTICS_NOTIFICATION 0x9d, below.
2730 * If the CLEAR_STATS configuration flag is set, uCode will clear its
2731 * internal copy of the statistics (counters) after issuing the response.
2732 * This flag does not affect STATISTICS_NOTIFICATIONs after beacons (see below).
2734 * If the DISABLE_NOTIF configuration flag is set, uCode will not issue
2735 * STATISTICS_NOTIFICATIONs after received beacons (see below). This flag
2736 * does not affect the response to the REPLY_STATISTICS_CMD 0x9c itself.
2738 #define IWL_STATS_CONF_CLEAR_STATS cpu_to_le32(0x1) /* see above */
2739 #define IWL_STATS_CONF_DISABLE_NOTIF cpu_to_le32(0x2)/* see above */
2740 struct iwl_statistics_cmd {
2741 __le32 configuration_flags; /* IWL_STATS_CONF_* */
2745 * STATISTICS_NOTIFICATION = 0x9d (notification only, not a command)
2747 * By default, uCode issues this notification after receiving a beacon
2748 * while associated. To disable this behavior, set DISABLE_NOTIF flag in the
2749 * REPLY_STATISTICS_CMD 0x9c, above.
2751 * Statistics counters continue to increment beacon after beacon, but are
2752 * cleared when changing channels or when driver issues REPLY_STATISTICS_CMD
2753 * 0x9c with CLEAR_STATS bit set (see above).
2755 * uCode also issues this notification during scans. uCode clears statistics
2756 * appropriately so that each notification contains statistics for only the
2757 * one channel that has just been scanned.
2759 #define STATISTICS_REPLY_FLG_BAND_24G_MSK cpu_to_le32(0x2)
2760 #define STATISTICS_REPLY_FLG_HT40_MODE_MSK cpu_to_le32(0x8)
2762 struct iwl_notif_statistics {
2764 struct statistics_rx rx;
2765 struct statistics_tx tx;
2766 struct statistics_general general;
2769 struct iwl_bt_notif_statistics {
2771 struct statistics_rx_bt rx;
2772 struct statistics_tx tx;
2773 struct statistics_general_bt general;
2777 * MISSED_BEACONS_NOTIFICATION = 0xa2 (notification only, not a command)
2779 * uCode send MISSED_BEACONS_NOTIFICATION to driver when detect beacon missed
2780 * in regardless of how many missed beacons, which mean when driver receive the
2781 * notification, inside the command, it can find all the beacons information
2782 * which include number of total missed beacons, number of consecutive missed
2783 * beacons, number of beacons received and number of beacons expected to
2786 * If uCode detected consecutive_missed_beacons > 5, it will reset the radio
2787 * in order to bring the radio/PHY back to working state; which has no relation
2788 * to when driver will perform sensitivity calibration.
2790 * Driver should set it own missed_beacon_threshold to decide when to perform
2791 * sensitivity calibration based on number of consecutive missed beacons in
2792 * order to improve overall performance, especially in noisy environment.
2796 #define IWL_MISSED_BEACON_THRESHOLD_MIN (1)
2797 #define IWL_MISSED_BEACON_THRESHOLD_DEF (5)
2798 #define IWL_MISSED_BEACON_THRESHOLD_MAX IWL_MISSED_BEACON_THRESHOLD_DEF
2800 struct iwl_missed_beacon_notif {
2801 __le32 consecutive_missed_beacons;
2802 __le32 total_missed_becons;
2803 __le32 num_expected_beacons;
2804 __le32 num_recvd_beacons;
2808 /******************************************************************************
2810 * Rx Calibration Commands:
2812 * With the uCode used for open source drivers, most Tx calibration (except
2813 * for Tx Power) and most Rx calibration is done by uCode during the
2814 * "initialize" phase of uCode boot. Driver must calibrate only:
2816 * 1) Tx power (depends on temperature), described elsewhere
2817 * 2) Receiver gain balance (optimize MIMO, and detect disconnected antennas)
2818 * 3) Receiver sensitivity (to optimize signal detection)
2820 *****************************************************************************/
2823 * SENSITIVITY_CMD = 0xa8 (command, has simple generic response)
2825 * This command sets up the Rx signal detector for a sensitivity level that
2826 * is high enough to lock onto all signals within the associated network,
2827 * but low enough to ignore signals that are below a certain threshold, so as
2828 * not to have too many "false alarms". False alarms are signals that the
2829 * Rx DSP tries to lock onto, but then discards after determining that they
2832 * The optimum number of false alarms is between 5 and 50 per 200 TUs
2833 * (200 * 1024 uSecs, i.e. 204.8 milliseconds) of actual Rx time (i.e.
2834 * time listening, not transmitting). Driver must adjust sensitivity so that
2835 * the ratio of actual false alarms to actual Rx time falls within this range.
2837 * While associated, uCode delivers STATISTICS_NOTIFICATIONs after each
2838 * received beacon. These provide information to the driver to analyze the
2839 * sensitivity. Don't analyze statistics that come in from scanning, or any
2840 * other non-associated-network source. Pertinent statistics include:
2842 * From "general" statistics (struct statistics_rx_non_phy):
2844 * (beacon_energy_[abc] & 0x0FF00) >> 8 (unsigned, higher value is lower level)
2845 * Measure of energy of desired signal. Used for establishing a level
2846 * below which the device does not detect signals.
2848 * (beacon_silence_rssi_[abc] & 0x0FF00) >> 8 (unsigned, units in dB)
2849 * Measure of background noise in silent period after beacon.
2852 * uSecs of actual Rx time during beacon period (varies according to
2853 * how much time was spent transmitting).
2855 * From "cck" and "ofdm" statistics (struct statistics_rx_phy), separately:
2858 * Signal locks abandoned early (before phy-level header).
2861 * Signal locks abandoned late (during phy-level header).
2863 * NOTE: Both false_alarm_cnt and plcp_err increment monotonically from
2864 * beacon to beacon, i.e. each value is an accumulation of all errors
2865 * before and including the latest beacon. Values will wrap around to 0
2866 * after counting up to 2^32 - 1. Driver must differentiate vs.
2867 * previous beacon's values to determine # false alarms in the current
2870 * Total number of false alarms = false_alarms + plcp_errs
2872 * For OFDM, adjust the following table entries in struct iwl_sensitivity_cmd
2873 * (notice that the start points for OFDM are at or close to settings for
2874 * maximum sensitivity):
2877 * HD_AUTO_CORR32_X1_TH_ADD_MIN_INDEX 90 / 85 / 120
2878 * HD_AUTO_CORR32_X1_TH_ADD_MIN_MRC_INDEX 170 / 170 / 210
2879 * HD_AUTO_CORR32_X4_TH_ADD_MIN_INDEX 105 / 105 / 140
2880 * HD_AUTO_CORR32_X4_TH_ADD_MIN_MRC_INDEX 220 / 220 / 270
2882 * If actual rate of OFDM false alarms (+ plcp_errors) is too high
2883 * (greater than 50 for each 204.8 msecs listening), reduce sensitivity
2884 * by *adding* 1 to all 4 of the table entries above, up to the max for
2885 * each entry. Conversely, if false alarm rate is too low (less than 5
2886 * for each 204.8 msecs listening), *subtract* 1 from each entry to
2887 * increase sensitivity.
2889 * For CCK sensitivity, keep track of the following:
2891 * 1). 20-beacon history of maximum background noise, indicated by
2892 * (beacon_silence_rssi_[abc] & 0x0FF00), units in dB, across the
2893 * 3 receivers. For any given beacon, the "silence reference" is
2894 * the maximum of last 60 samples (20 beacons * 3 receivers).
2896 * 2). 10-beacon history of strongest signal level, as indicated
2897 * by (beacon_energy_[abc] & 0x0FF00) >> 8, across the 3 receivers,
2898 * i.e. the strength of the signal through the best receiver at the
2899 * moment. These measurements are "upside down", with lower values
2900 * for stronger signals, so max energy will be *minimum* value.
2902 * Then for any given beacon, the driver must determine the *weakest*
2903 * of the strongest signals; this is the minimum level that needs to be
2904 * successfully detected, when using the best receiver at the moment.
2905 * "Max cck energy" is the maximum (higher value means lower energy!)
2906 * of the last 10 minima. Once this is determined, driver must add
2907 * a little margin by adding "6" to it.
2909 * 3). Number of consecutive beacon periods with too few false alarms.
2910 * Reset this to 0 at the first beacon period that falls within the
2911 * "good" range (5 to 50 false alarms per 204.8 milliseconds rx).
2913 * Then, adjust the following CCK table entries in struct iwl_sensitivity_cmd
2914 * (notice that the start points for CCK are at maximum sensitivity):
2917 * HD_AUTO_CORR40_X4_TH_ADD_MIN_INDEX 125 / 125 / 200
2918 * HD_AUTO_CORR40_X4_TH_ADD_MIN_MRC_INDEX 200 / 200 / 400
2919 * HD_MIN_ENERGY_CCK_DET_INDEX 100 / 0 / 100
2921 * If actual rate of CCK false alarms (+ plcp_errors) is too high
2922 * (greater than 50 for each 204.8 msecs listening), method for reducing
2925 * 1) *Add* 3 to value in HD_AUTO_CORR40_X4_TH_ADD_MIN_MRC_INDEX,
2928 * 2) If current value in HD_AUTO_CORR40_X4_TH_ADD_MIN_INDEX is < 160,
2929 * sensitivity has been reduced a significant amount; bring it up to
2930 * a moderate 161. Otherwise, *add* 3, up to max 200.
2932 * 3) a) If current value in HD_AUTO_CORR40_X4_TH_ADD_MIN_INDEX is > 160,
2933 * sensitivity has been reduced only a moderate or small amount;
2934 * *subtract* 2 from value in HD_MIN_ENERGY_CCK_DET_INDEX,
2935 * down to min 0. Otherwise (if gain has been significantly reduced),
2936 * don't change the HD_MIN_ENERGY_CCK_DET_INDEX value.
2938 * b) Save a snapshot of the "silence reference".
2940 * If actual rate of CCK false alarms (+ plcp_errors) is too low
2941 * (less than 5 for each 204.8 msecs listening), method for increasing
2942 * sensitivity is used only if:
2944 * 1a) Previous beacon did not have too many false alarms
2945 * 1b) AND difference between previous "silence reference" and current
2946 * "silence reference" (prev - current) is 2 or more,
2947 * OR 2) 100 or more consecutive beacon periods have had rate of
2948 * less than 5 false alarms per 204.8 milliseconds rx time.
2950 * Method for increasing sensitivity:
2952 * 1) *Subtract* 3 from value in HD_AUTO_CORR40_X4_TH_ADD_MIN_INDEX,
2955 * 2) *Subtract* 3 from value in HD_AUTO_CORR40_X4_TH_ADD_MIN_MRC_INDEX,
2958 * 3) *Add* 2 to value in HD_MIN_ENERGY_CCK_DET_INDEX, up to max 100.
2960 * If actual rate of CCK false alarms (+ plcp_errors) is within good range
2961 * (between 5 and 50 for each 204.8 msecs listening):
2963 * 1) Save a snapshot of the silence reference.
2965 * 2) If previous beacon had too many CCK false alarms (+ plcp_errors),
2966 * give some extra margin to energy threshold by *subtracting* 8
2967 * from value in HD_MIN_ENERGY_CCK_DET_INDEX.
2969 * For all cases (too few, too many, good range), make sure that the CCK
2970 * detection threshold (energy) is below the energy level for robust
2971 * detection over the past 10 beacon periods, the "Max cck energy".
2972 * Lower values mean higher energy; this means making sure that the value
2973 * in HD_MIN_ENERGY_CCK_DET_INDEX is at or *above* "Max cck energy".
2978 * Table entries in SENSITIVITY_CMD (struct iwl_sensitivity_cmd)
2980 #define HD_TABLE_SIZE (11) /* number of entries */
2981 #define HD_MIN_ENERGY_CCK_DET_INDEX (0) /* table indexes */
2982 #define HD_MIN_ENERGY_OFDM_DET_INDEX (1)
2983 #define HD_AUTO_CORR32_X1_TH_ADD_MIN_INDEX (2)
2984 #define HD_AUTO_CORR32_X1_TH_ADD_MIN_MRC_INDEX (3)
2985 #define HD_AUTO_CORR40_X4_TH_ADD_MIN_MRC_INDEX (4)
2986 #define HD_AUTO_CORR32_X4_TH_ADD_MIN_INDEX (5)
2987 #define HD_AUTO_CORR32_X4_TH_ADD_MIN_MRC_INDEX (6)
2988 #define HD_BARKER_CORR_TH_ADD_MIN_INDEX (7)
2989 #define HD_BARKER_CORR_TH_ADD_MIN_MRC_INDEX (8)
2990 #define HD_AUTO_CORR40_X4_TH_ADD_MIN_INDEX (9)
2991 #define HD_OFDM_ENERGY_TH_IN_INDEX (10)
2994 * Additional table entries in enhance SENSITIVITY_CMD
2996 #define HD_INA_NON_SQUARE_DET_OFDM_INDEX (11)
2997 #define HD_INA_NON_SQUARE_DET_CCK_INDEX (12)
2998 #define HD_CORR_11_INSTEAD_OF_CORR_9_EN_INDEX (13)
2999 #define HD_OFDM_NON_SQUARE_DET_SLOPE_MRC_INDEX (14)
3000 #define HD_OFDM_NON_SQUARE_DET_INTERCEPT_MRC_INDEX (15)
3001 #define HD_OFDM_NON_SQUARE_DET_SLOPE_INDEX (16)
3002 #define HD_OFDM_NON_SQUARE_DET_INTERCEPT_INDEX (17)
3003 #define HD_CCK_NON_SQUARE_DET_SLOPE_MRC_INDEX (18)
3004 #define HD_CCK_NON_SQUARE_DET_INTERCEPT_MRC_INDEX (19)
3005 #define HD_CCK_NON_SQUARE_DET_SLOPE_INDEX (20)
3006 #define HD_CCK_NON_SQUARE_DET_INTERCEPT_INDEX (21)
3007 #define HD_RESERVED (22)
3009 /* number of entries for enhanced tbl */
3010 #define ENHANCE_HD_TABLE_SIZE (23)
3012 /* number of additional entries for enhanced tbl */
3013 #define ENHANCE_HD_TABLE_ENTRIES (ENHANCE_HD_TABLE_SIZE - HD_TABLE_SIZE)
3015 #define HD_INA_NON_SQUARE_DET_OFDM_DATA_V1 cpu_to_le16(0)
3016 #define HD_INA_NON_SQUARE_DET_CCK_DATA_V1 cpu_to_le16(0)
3017 #define HD_CORR_11_INSTEAD_OF_CORR_9_EN_DATA_V1 cpu_to_le16(0)
3018 #define HD_OFDM_NON_SQUARE_DET_SLOPE_MRC_DATA_V1 cpu_to_le16(668)
3019 #define HD_OFDM_NON_SQUARE_DET_INTERCEPT_MRC_DATA_V1 cpu_to_le16(4)
3020 #define HD_OFDM_NON_SQUARE_DET_SLOPE_DATA_V1 cpu_to_le16(486)
3021 #define HD_OFDM_NON_SQUARE_DET_INTERCEPT_DATA_V1 cpu_to_le16(37)
3022 #define HD_CCK_NON_SQUARE_DET_SLOPE_MRC_DATA_V1 cpu_to_le16(853)
3023 #define HD_CCK_NON_SQUARE_DET_INTERCEPT_MRC_DATA_V1 cpu_to_le16(4)
3024 #define HD_CCK_NON_SQUARE_DET_SLOPE_DATA_V1 cpu_to_le16(476)
3025 #define HD_CCK_NON_SQUARE_DET_INTERCEPT_DATA_V1 cpu_to_le16(99)
3027 #define HD_INA_NON_SQUARE_DET_OFDM_DATA_V2 cpu_to_le16(1)
3028 #define HD_INA_NON_SQUARE_DET_CCK_DATA_V2 cpu_to_le16(1)
3029 #define HD_CORR_11_INSTEAD_OF_CORR_9_EN_DATA_V2 cpu_to_le16(1)
3030 #define HD_OFDM_NON_SQUARE_DET_SLOPE_MRC_DATA_V2 cpu_to_le16(600)
3031 #define HD_OFDM_NON_SQUARE_DET_INTERCEPT_MRC_DATA_V2 cpu_to_le16(40)
3032 #define HD_OFDM_NON_SQUARE_DET_SLOPE_DATA_V2 cpu_to_le16(486)
3033 #define HD_OFDM_NON_SQUARE_DET_INTERCEPT_DATA_V2 cpu_to_le16(45)
3034 #define HD_CCK_NON_SQUARE_DET_SLOPE_MRC_DATA_V2 cpu_to_le16(853)
3035 #define HD_CCK_NON_SQUARE_DET_INTERCEPT_MRC_DATA_V2 cpu_to_le16(60)
3036 #define HD_CCK_NON_SQUARE_DET_SLOPE_DATA_V2 cpu_to_le16(476)
3037 #define HD_CCK_NON_SQUARE_DET_INTERCEPT_DATA_V2 cpu_to_le16(99)
3040 /* Control field in struct iwl_sensitivity_cmd */
3041 #define SENSITIVITY_CMD_CONTROL_DEFAULT_TABLE cpu_to_le16(0)
3042 #define SENSITIVITY_CMD_CONTROL_WORK_TABLE cpu_to_le16(1)
3045 * struct iwl_sensitivity_cmd
3046 * @control: (1) updates working table, (0) updates default table
3047 * @table: energy threshold values, use HD_* as index into table
3049 * Always use "1" in "control" to update uCode's working table and DSP.
3051 struct iwl_sensitivity_cmd {
3052 __le16 control; /* always use "1" */
3053 __le16 table[HD_TABLE_SIZE]; /* use HD_* as index */
3059 struct iwl_enhance_sensitivity_cmd {
3060 __le16 control; /* always use "1" */
3061 __le16 enhance_table[ENHANCE_HD_TABLE_SIZE]; /* use HD_* as index */
3066 * REPLY_PHY_CALIBRATION_CMD = 0xb0 (command, has simple generic response)
3068 * This command sets the relative gains of agn device's 3 radio receiver chains.
3070 * After the first association, driver should accumulate signal and noise
3071 * statistics from the STATISTICS_NOTIFICATIONs that follow the first 20
3072 * beacons from the associated network (don't collect statistics that come
3073 * in from scanning, or any other non-network source).
3075 * DISCONNECTED ANTENNA:
3077 * Driver should determine which antennas are actually connected, by comparing
3078 * average beacon signal levels for the 3 Rx chains. Accumulate (add) the
3079 * following values over 20 beacons, one accumulator for each of the chains
3080 * a/b/c, from struct statistics_rx_non_phy:
3082 * beacon_rssi_[abc] & 0x0FF (unsigned, units in dB)
3084 * Find the strongest signal from among a/b/c. Compare the other two to the
3085 * strongest. If any signal is more than 15 dB (times 20, unless you
3086 * divide the accumulated values by 20) below the strongest, the driver
3087 * considers that antenna to be disconnected, and should not try to use that
3088 * antenna/chain for Rx or Tx. If both A and B seem to be disconnected,
3089 * driver should declare the stronger one as connected, and attempt to use it
3090 * (A and B are the only 2 Tx chains!).
3095 * Driver should balance the 3 receivers (but just the ones that are connected
3096 * to antennas, see above) for gain, by comparing the average signal levels
3097 * detected during the silence after each beacon (background noise).
3098 * Accumulate (add) the following values over 20 beacons, one accumulator for
3099 * each of the chains a/b/c, from struct statistics_rx_non_phy:
3101 * beacon_silence_rssi_[abc] & 0x0FF (unsigned, units in dB)
3103 * Find the weakest background noise level from among a/b/c. This Rx chain
3104 * will be the reference, with 0 gain adjustment. Attenuate other channels by
3105 * finding noise difference:
3107 * (accum_noise[i] - accum_noise[reference]) / 30
3109 * The "30" adjusts the dB in the 20 accumulated samples to units of 1.5 dB.
3110 * For use in diff_gain_[abc] fields of struct iwl_calibration_cmd, the
3111 * driver should limit the difference results to a range of 0-3 (0-4.5 dB),
3112 * and set bit 2 to indicate "reduce gain". The value for the reference
3113 * (weakest) chain should be "0".
3115 * diff_gain_[abc] bit fields:
3116 * 2: (1) reduce gain, (0) increase gain
3117 * 1-0: amount of gain, units of 1.5 dB
3120 /* Phy calibration command for series */
3122 IWL_PHY_CALIBRATE_DC_CMD = 8,
3123 IWL_PHY_CALIBRATE_LO_CMD = 9,
3124 IWL_PHY_CALIBRATE_TX_IQ_CMD = 11,
3125 IWL_PHY_CALIBRATE_CRYSTAL_FRQ_CMD = 15,
3126 IWL_PHY_CALIBRATE_BASE_BAND_CMD = 16,
3127 IWL_PHY_CALIBRATE_TX_IQ_PERD_CMD = 17,
3128 IWL_PHY_CALIBRATE_TEMP_OFFSET_CMD = 18,
3131 /* This enum defines the bitmap of various calibrations to enable in both
3132 * init ucode and runtime ucode through CALIBRATION_CFG_CMD.
3134 enum iwl_ucode_calib_cfg {
3135 IWL_CALIB_CFG_RX_BB_IDX = BIT(0),
3136 IWL_CALIB_CFG_DC_IDX = BIT(1),
3137 IWL_CALIB_CFG_LO_IDX = BIT(2),
3138 IWL_CALIB_CFG_TX_IQ_IDX = BIT(3),
3139 IWL_CALIB_CFG_RX_IQ_IDX = BIT(4),
3140 IWL_CALIB_CFG_NOISE_IDX = BIT(5),
3141 IWL_CALIB_CFG_CRYSTAL_IDX = BIT(6),
3142 IWL_CALIB_CFG_TEMPERATURE_IDX = BIT(7),
3143 IWL_CALIB_CFG_PAPD_IDX = BIT(8),
3144 IWL_CALIB_CFG_SENSITIVITY_IDX = BIT(9),
3145 IWL_CALIB_CFG_TX_PWR_IDX = BIT(10),
3148 #define IWL_CALIB_INIT_CFG_ALL cpu_to_le32(IWL_CALIB_CFG_RX_BB_IDX | \
3149 IWL_CALIB_CFG_DC_IDX | \
3150 IWL_CALIB_CFG_LO_IDX | \
3151 IWL_CALIB_CFG_TX_IQ_IDX | \
3152 IWL_CALIB_CFG_RX_IQ_IDX | \
3153 IWL_CALIB_CFG_CRYSTAL_IDX)
3155 #define IWL_CALIB_RT_CFG_ALL cpu_to_le32(IWL_CALIB_CFG_RX_BB_IDX | \
3156 IWL_CALIB_CFG_DC_IDX | \
3157 IWL_CALIB_CFG_LO_IDX | \
3158 IWL_CALIB_CFG_TX_IQ_IDX | \
3159 IWL_CALIB_CFG_RX_IQ_IDX | \
3160 IWL_CALIB_CFG_TEMPERATURE_IDX | \
3161 IWL_CALIB_CFG_PAPD_IDX | \
3162 IWL_CALIB_CFG_TX_PWR_IDX | \
3163 IWL_CALIB_CFG_CRYSTAL_IDX)
3165 #define IWL_CALIB_CFG_FLAG_SEND_COMPLETE_NTFY_MSK cpu_to_le32(BIT(0))
3167 struct iwl_calib_cfg_elmnt_s {
3175 struct iwl_calib_cfg_status_s {
3176 struct iwl_calib_cfg_elmnt_s once;
3177 struct iwl_calib_cfg_elmnt_s perd;
3181 struct iwl_calib_cfg_cmd {
3182 struct iwl_calib_cfg_status_s ucd_calib_cfg;
3183 struct iwl_calib_cfg_status_s drv_calib_cfg;
3187 struct iwl_calib_hdr {
3194 struct iwl_calib_cmd {
3195 struct iwl_calib_hdr hdr;
3199 struct iwl_calib_xtal_freq_cmd {
3200 struct iwl_calib_hdr hdr;
3206 #define DEFAULT_RADIO_SENSOR_OFFSET cpu_to_le16(2700)
3207 struct iwl_calib_temperature_offset_cmd {
3208 struct iwl_calib_hdr hdr;
3209 __le16 radio_sensor_offset;
3213 struct iwl_calib_temperature_offset_v2_cmd {
3214 struct iwl_calib_hdr hdr;
3215 __le16 radio_sensor_offset_high;
3216 __le16 radio_sensor_offset_low;
3217 __le16 burntVoltageRef;
3221 /* IWL_PHY_CALIBRATE_CHAIN_NOISE_RESET_CMD */
3222 struct iwl_calib_chain_noise_reset_cmd {
3223 struct iwl_calib_hdr hdr;
3227 /* IWL_PHY_CALIBRATE_CHAIN_NOISE_GAIN_CMD */
3228 struct iwl_calib_chain_noise_gain_cmd {
3229 struct iwl_calib_hdr hdr;
3235 /******************************************************************************
3237 * Miscellaneous Commands:
3239 *****************************************************************************/
3242 * LEDs Command & Response
3243 * REPLY_LEDS_CMD = 0x48 (command, has simple generic response)
3245 * For each of 3 possible LEDs (Activity/Link/Tech, selected by "id" field),
3246 * this command turns it on or off, or sets up a periodic blinking cycle.
3248 struct iwl_led_cmd {
3249 __le32 interval; /* "interval" in uSec */
3250 u8 id; /* 1: Activity, 2: Link, 3: Tech */
3251 u8 off; /* # intervals off while blinking;
3252 * "0", with >0 "on" value, turns LED on */
3253 u8 on; /* # intervals on while blinking;
3254 * "0", regardless of "off", turns LED off */
3259 * station priority table entries
3260 * also used as potential "events" value for both
3261 * COEX_MEDIUM_NOTIFICATION and COEX_EVENT_CMD
3265 * COEX events entry flag masks
3266 * RP - Requested Priority
3267 * WP - Win Medium Priority: priority assigned when the contention has been won
3269 #define COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG (0x1)
3270 #define COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG (0x2)
3271 #define COEX_EVT_FLAG_DELAY_MEDIUM_FREE_NTFY_FLG (0x4)
3273 #define COEX_CU_UNASSOC_IDLE_RP 4
3274 #define COEX_CU_UNASSOC_MANUAL_SCAN_RP 4
3275 #define COEX_CU_UNASSOC_AUTO_SCAN_RP 4
3276 #define COEX_CU_CALIBRATION_RP 4
3277 #define COEX_CU_PERIODIC_CALIBRATION_RP 4
3278 #define COEX_CU_CONNECTION_ESTAB_RP 4
3279 #define COEX_CU_ASSOCIATED_IDLE_RP 4
3280 #define COEX_CU_ASSOC_MANUAL_SCAN_RP 4
3281 #define COEX_CU_ASSOC_AUTO_SCAN_RP 4
3282 #define COEX_CU_ASSOC_ACTIVE_LEVEL_RP 4
3283 #define COEX_CU_RF_ON_RP 6
3284 #define COEX_CU_RF_OFF_RP 4
3285 #define COEX_CU_STAND_ALONE_DEBUG_RP 6
3286 #define COEX_CU_IPAN_ASSOC_LEVEL_RP 4
3287 #define COEX_CU_RSRVD1_RP 4
3288 #define COEX_CU_RSRVD2_RP 4
3290 #define COEX_CU_UNASSOC_IDLE_WP 3
3291 #define COEX_CU_UNASSOC_MANUAL_SCAN_WP 3
3292 #define COEX_CU_UNASSOC_AUTO_SCAN_WP 3
3293 #define COEX_CU_CALIBRATION_WP 3
3294 #define COEX_CU_PERIODIC_CALIBRATION_WP 3
3295 #define COEX_CU_CONNECTION_ESTAB_WP 3
3296 #define COEX_CU_ASSOCIATED_IDLE_WP 3
3297 #define COEX_CU_ASSOC_MANUAL_SCAN_WP 3
3298 #define COEX_CU_ASSOC_AUTO_SCAN_WP 3
3299 #define COEX_CU_ASSOC_ACTIVE_LEVEL_WP 3
3300 #define COEX_CU_RF_ON_WP 3
3301 #define COEX_CU_RF_OFF_WP 3
3302 #define COEX_CU_STAND_ALONE_DEBUG_WP 6
3303 #define COEX_CU_IPAN_ASSOC_LEVEL_WP 3
3304 #define COEX_CU_RSRVD1_WP 3
3305 #define COEX_CU_RSRVD2_WP 3
3307 #define COEX_UNASSOC_IDLE_FLAGS 0
3308 #define COEX_UNASSOC_MANUAL_SCAN_FLAGS \
3309 (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
3310 COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG)
3311 #define COEX_UNASSOC_AUTO_SCAN_FLAGS \
3312 (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
3313 COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG)
3314 #define COEX_CALIBRATION_FLAGS \
3315 (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
3316 COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG)
3317 #define COEX_PERIODIC_CALIBRATION_FLAGS 0
3319 * COEX_CONNECTION_ESTAB:
3320 * we need DELAY_MEDIUM_FREE_NTFY to let WiMAX disconnect from network.
3322 #define COEX_CONNECTION_ESTAB_FLAGS \
3323 (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
3324 COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG | \
3325 COEX_EVT_FLAG_DELAY_MEDIUM_FREE_NTFY_FLG)
3326 #define COEX_ASSOCIATED_IDLE_FLAGS 0
3327 #define COEX_ASSOC_MANUAL_SCAN_FLAGS \
3328 (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
3329 COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG)
3330 #define COEX_ASSOC_AUTO_SCAN_FLAGS \
3331 (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
3332 COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG)
3333 #define COEX_ASSOC_ACTIVE_LEVEL_FLAGS 0
3334 #define COEX_RF_ON_FLAGS 0
3335 #define COEX_RF_OFF_FLAGS 0
3336 #define COEX_STAND_ALONE_DEBUG_FLAGS \
3337 (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
3338 COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG)
3339 #define COEX_IPAN_ASSOC_LEVEL_FLAGS \
3340 (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
3341 COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG | \
3342 COEX_EVT_FLAG_DELAY_MEDIUM_FREE_NTFY_FLG)
3343 #define COEX_RSRVD1_FLAGS 0
3344 #define COEX_RSRVD2_FLAGS 0
3346 * COEX_CU_RF_ON is the event wrapping all radio ownership.
3347 * We need DELAY_MEDIUM_FREE_NTFY to let WiMAX disconnect from network.
3349 #define COEX_CU_RF_ON_FLAGS \
3350 (COEX_EVT_FLAG_MEDIUM_FREE_NTFY_FLG | \
3351 COEX_EVT_FLAG_MEDIUM_ACTV_NTFY_FLG | \
3352 COEX_EVT_FLAG_DELAY_MEDIUM_FREE_NTFY_FLG)
3356 /* un-association part */
3357 COEX_UNASSOC_IDLE = 0,
3358 COEX_UNASSOC_MANUAL_SCAN = 1,
3359 COEX_UNASSOC_AUTO_SCAN = 2,
3361 COEX_CALIBRATION = 3,
3362 COEX_PERIODIC_CALIBRATION = 4,
3364 COEX_CONNECTION_ESTAB = 5,
3365 /* association part */
3366 COEX_ASSOCIATED_IDLE = 6,
3367 COEX_ASSOC_MANUAL_SCAN = 7,
3368 COEX_ASSOC_AUTO_SCAN = 8,
3369 COEX_ASSOC_ACTIVE_LEVEL = 9,
3373 COEX_STAND_ALONE_DEBUG = 12,
3375 COEX_IPAN_ASSOC_LEVEL = 13,
3379 COEX_NUM_OF_EVENTS = 16
3383 * Coexistence WIFI/WIMAX Command
3384 * COEX_PRIORITY_TABLE_CMD = 0x5a
3387 struct iwl_wimax_coex_event_entry {
3394 /* COEX flag masks */
3396 /* Station table is valid */
3397 #define COEX_FLAGS_STA_TABLE_VALID_MSK (0x1)
3398 /* UnMask wake up src at unassociated sleep */
3399 #define COEX_FLAGS_UNASSOC_WA_UNMASK_MSK (0x4)
3400 /* UnMask wake up src at associated sleep */
3401 #define COEX_FLAGS_ASSOC_WA_UNMASK_MSK (0x8)
3402 /* Enable CoEx feature. */
3403 #define COEX_FLAGS_COEX_ENABLE_MSK (0x80)
3405 struct iwl_wimax_coex_cmd {
3408 struct iwl_wimax_coex_event_entry sta_prio[COEX_NUM_OF_EVENTS];
3412 * Coexistence MEDIUM NOTIFICATION
3413 * COEX_MEDIUM_NOTIFICATION = 0x5b
3415 * notification from uCode to host to indicate medium changes
3420 * bit 0 - 2: medium status
3421 * bit 3: medium change indication
3422 * bit 4 - 31: reserved
3424 /* status option values, (0 - 2 bits) */
3425 #define COEX_MEDIUM_BUSY (0x0) /* radio belongs to WiMAX */
3426 #define COEX_MEDIUM_ACTIVE (0x1) /* radio belongs to WiFi */
3427 #define COEX_MEDIUM_PRE_RELEASE (0x2) /* received radio release */
3428 #define COEX_MEDIUM_MSK (0x7)
3430 /* send notification status (1 bit) */
3431 #define COEX_MEDIUM_CHANGED (0x8)
3432 #define COEX_MEDIUM_CHANGED_MSK (0x8)
3433 #define COEX_MEDIUM_SHIFT (3)
3435 struct iwl_coex_medium_notification {
3441 * Coexistence EVENT Command
3442 * COEX_EVENT_CMD = 0x5c
3444 * send from host to uCode for coex event request.
3447 #define COEX_EVENT_REQUEST_MSK (0x1)
3449 struct iwl_coex_event_cmd {
3455 struct iwl_coex_event_resp {
3460 /******************************************************************************
3461 * Bluetooth Coexistence commands
3463 *****************************************************************************/
3466 * BT Status notification
3467 * REPLY_BT_COEX_PROFILE_NOTIF = 0xce
3469 enum iwl_bt_coex_profile_traffic_load {
3470 IWL_BT_COEX_TRAFFIC_LOAD_NONE = 0,
3471 IWL_BT_COEX_TRAFFIC_LOAD_LOW = 1,
3472 IWL_BT_COEX_TRAFFIC_LOAD_HIGH = 2,
3473 IWL_BT_COEX_TRAFFIC_LOAD_CONTINUOUS = 3,
3475 * There are no more even though below is a u8, the
3476 * indication from the BT device only has two bits.
3480 #define BT_SESSION_ACTIVITY_1_UART_MSG 0x1
3481 #define BT_SESSION_ACTIVITY_2_UART_MSG 0x2
3483 /* BT UART message - Share Part (BT -> WiFi) */
3484 #define BT_UART_MSG_FRAME1MSGTYPE_POS (0)
3485 #define BT_UART_MSG_FRAME1MSGTYPE_MSK \
3486 (0x7 << BT_UART_MSG_FRAME1MSGTYPE_POS)
3487 #define BT_UART_MSG_FRAME1SSN_POS (3)
3488 #define BT_UART_MSG_FRAME1SSN_MSK \
3489 (0x3 << BT_UART_MSG_FRAME1SSN_POS)
3490 #define BT_UART_MSG_FRAME1UPDATEREQ_POS (5)
3491 #define BT_UART_MSG_FRAME1UPDATEREQ_MSK \
3492 (0x1 << BT_UART_MSG_FRAME1UPDATEREQ_POS)
3493 #define BT_UART_MSG_FRAME1RESERVED_POS (6)
3494 #define BT_UART_MSG_FRAME1RESERVED_MSK \
3495 (0x3 << BT_UART_MSG_FRAME1RESERVED_POS)
3497 #define BT_UART_MSG_FRAME2OPENCONNECTIONS_POS (0)
3498 #define BT_UART_MSG_FRAME2OPENCONNECTIONS_MSK \
3499 (0x3 << BT_UART_MSG_FRAME2OPENCONNECTIONS_POS)
3500 #define BT_UART_MSG_FRAME2TRAFFICLOAD_POS (2)
3501 #define BT_UART_MSG_FRAME2TRAFFICLOAD_MSK \
3502 (0x3 << BT_UART_MSG_FRAME2TRAFFICLOAD_POS)
3503 #define BT_UART_MSG_FRAME2CHLSEQN_POS (4)
3504 #define BT_UART_MSG_FRAME2CHLSEQN_MSK \
3505 (0x1 << BT_UART_MSG_FRAME2CHLSEQN_POS)
3506 #define BT_UART_MSG_FRAME2INBAND_POS (5)
3507 #define BT_UART_MSG_FRAME2INBAND_MSK \
3508 (0x1 << BT_UART_MSG_FRAME2INBAND_POS)
3509 #define BT_UART_MSG_FRAME2RESERVED_POS (6)
3510 #define BT_UART_MSG_FRAME2RESERVED_MSK \
3511 (0x3 << BT_UART_MSG_FRAME2RESERVED_POS)
3513 #define BT_UART_MSG_FRAME3SCOESCO_POS (0)
3514 #define BT_UART_MSG_FRAME3SCOESCO_MSK \
3515 (0x1 << BT_UART_MSG_FRAME3SCOESCO_POS)
3516 #define BT_UART_MSG_FRAME3SNIFF_POS (1)
3517 #define BT_UART_MSG_FRAME3SNIFF_MSK \
3518 (0x1 << BT_UART_MSG_FRAME3SNIFF_POS)
3519 #define BT_UART_MSG_FRAME3A2DP_POS (2)
3520 #define BT_UART_MSG_FRAME3A2DP_MSK \
3521 (0x1 << BT_UART_MSG_FRAME3A2DP_POS)
3522 #define BT_UART_MSG_FRAME3ACL_POS (3)
3523 #define BT_UART_MSG_FRAME3ACL_MSK \
3524 (0x1 << BT_UART_MSG_FRAME3ACL_POS)
3525 #define BT_UART_MSG_FRAME3MASTER_POS (4)
3526 #define BT_UART_MSG_FRAME3MASTER_MSK \
3527 (0x1 << BT_UART_MSG_FRAME3MASTER_POS)
3528 #define BT_UART_MSG_FRAME3OBEX_POS (5)
3529 #define BT_UART_MSG_FRAME3OBEX_MSK \
3530 (0x1 << BT_UART_MSG_FRAME3OBEX_POS)
3531 #define BT_UART_MSG_FRAME3RESERVED_POS (6)
3532 #define BT_UART_MSG_FRAME3RESERVED_MSK \
3533 (0x3 << BT_UART_MSG_FRAME3RESERVED_POS)
3535 #define BT_UART_MSG_FRAME4IDLEDURATION_POS (0)
3536 #define BT_UART_MSG_FRAME4IDLEDURATION_MSK \
3537 (0x3F << BT_UART_MSG_FRAME4IDLEDURATION_POS)
3538 #define BT_UART_MSG_FRAME4RESERVED_POS (6)
3539 #define BT_UART_MSG_FRAME4RESERVED_MSK \
3540 (0x3 << BT_UART_MSG_FRAME4RESERVED_POS)
3542 #define BT_UART_MSG_FRAME5TXACTIVITY_POS (0)
3543 #define BT_UART_MSG_FRAME5TXACTIVITY_MSK \
3544 (0x3 << BT_UART_MSG_FRAME5TXACTIVITY_POS)
3545 #define BT_UART_MSG_FRAME5RXACTIVITY_POS (2)
3546 #define BT_UART_MSG_FRAME5RXACTIVITY_MSK \
3547 (0x3 << BT_UART_MSG_FRAME5RXACTIVITY_POS)
3548 #define BT_UART_MSG_FRAME5ESCORETRANSMIT_POS (4)
3549 #define BT_UART_MSG_FRAME5ESCORETRANSMIT_MSK \
3550 (0x3 << BT_UART_MSG_FRAME5ESCORETRANSMIT_POS)
3551 #define BT_UART_MSG_FRAME5RESERVED_POS (6)
3552 #define BT_UART_MSG_FRAME5RESERVED_MSK \
3553 (0x3 << BT_UART_MSG_FRAME5RESERVED_POS)
3555 #define BT_UART_MSG_FRAME6SNIFFINTERVAL_POS (0)
3556 #define BT_UART_MSG_FRAME6SNIFFINTERVAL_MSK \
3557 (0x1F << BT_UART_MSG_FRAME6SNIFFINTERVAL_POS)
3558 #define BT_UART_MSG_FRAME6DISCOVERABLE_POS (5)
3559 #define BT_UART_MSG_FRAME6DISCOVERABLE_MSK \
3560 (0x1 << BT_UART_MSG_FRAME6DISCOVERABLE_POS)
3561 #define BT_UART_MSG_FRAME6RESERVED_POS (6)
3562 #define BT_UART_MSG_FRAME6RESERVED_MSK \
3563 (0x3 << BT_UART_MSG_FRAME6RESERVED_POS)
3565 #define BT_UART_MSG_FRAME7SNIFFACTIVITY_POS (0)
3566 #define BT_UART_MSG_FRAME7SNIFFACTIVITY_MSK \
3567 (0x7 << BT_UART_MSG_FRAME7SNIFFACTIVITY_POS)
3568 #define BT_UART_MSG_FRAME7PAGE_POS (3)
3569 #define BT_UART_MSG_FRAME7PAGE_MSK \
3570 (0x1 << BT_UART_MSG_FRAME7PAGE_POS)
3571 #define BT_UART_MSG_FRAME7INQUIRY_POS (4)
3572 #define BT_UART_MSG_FRAME7INQUIRY_MSK \
3573 (0x1 << BT_UART_MSG_FRAME7INQUIRY_POS)
3574 #define BT_UART_MSG_FRAME7CONNECTABLE_POS (5)
3575 #define BT_UART_MSG_FRAME7CONNECTABLE_MSK \
3576 (0x1 << BT_UART_MSG_FRAME7CONNECTABLE_POS)
3577 #define BT_UART_MSG_FRAME7RESERVED_POS (6)
3578 #define BT_UART_MSG_FRAME7RESERVED_MSK \
3579 (0x3 << BT_UART_MSG_FRAME7RESERVED_POS)
3581 /* BT Session Activity 2 UART message (BT -> WiFi) */
3582 #define BT_UART_MSG_2_FRAME1RESERVED1_POS (5)
3583 #define BT_UART_MSG_2_FRAME1RESERVED1_MSK \
3584 (0x1<<BT_UART_MSG_2_FRAME1RESERVED1_POS)
3585 #define BT_UART_MSG_2_FRAME1RESERVED2_POS (6)
3586 #define BT_UART_MSG_2_FRAME1RESERVED2_MSK \
3587 (0x3<<BT_UART_MSG_2_FRAME1RESERVED2_POS)
3589 #define BT_UART_MSG_2_FRAME2AGGTRAFFICLOAD_POS (0)
3590 #define BT_UART_MSG_2_FRAME2AGGTRAFFICLOAD_MSK \
3591 (0x3F<<BT_UART_MSG_2_FRAME2AGGTRAFFICLOAD_POS)
3592 #define BT_UART_MSG_2_FRAME2RESERVED_POS (6)
3593 #define BT_UART_MSG_2_FRAME2RESERVED_MSK \
3594 (0x3<<BT_UART_MSG_2_FRAME2RESERVED_POS)
3596 #define BT_UART_MSG_2_FRAME3BRLASTTXPOWER_POS (0)
3597 #define BT_UART_MSG_2_FRAME3BRLASTTXPOWER_MSK \
3598 (0xF<<BT_UART_MSG_2_FRAME3BRLASTTXPOWER_POS)
3599 #define BT_UART_MSG_2_FRAME3INQPAGESRMODE_POS (4)
3600 #define BT_UART_MSG_2_FRAME3INQPAGESRMODE_MSK \
3601 (0x1<<BT_UART_MSG_2_FRAME3INQPAGESRMODE_POS)
3602 #define BT_UART_MSG_2_FRAME3LEMASTER_POS (5)
3603 #define BT_UART_MSG_2_FRAME3LEMASTER_MSK \
3604 (0x1<<BT_UART_MSG_2_FRAME3LEMASTER_POS)
3605 #define BT_UART_MSG_2_FRAME3RESERVED_POS (6)
3606 #define BT_UART_MSG_2_FRAME3RESERVED_MSK \
3607 (0x3<<BT_UART_MSG_2_FRAME3RESERVED_POS)
3609 #define BT_UART_MSG_2_FRAME4LELASTTXPOWER_POS (0)
3610 #define BT_UART_MSG_2_FRAME4LELASTTXPOWER_MSK \
3611 (0xF<<BT_UART_MSG_2_FRAME4LELASTTXPOWER_POS)
3612 #define BT_UART_MSG_2_FRAME4NUMLECONN_POS (4)
3613 #define BT_UART_MSG_2_FRAME4NUMLECONN_MSK \
3614 (0x3<<BT_UART_MSG_2_FRAME4NUMLECONN_POS)
3615 #define BT_UART_MSG_2_FRAME4RESERVED_POS (6)
3616 #define BT_UART_MSG_2_FRAME4RESERVED_MSK \
3617 (0x3<<BT_UART_MSG_2_FRAME4RESERVED_POS)
3619 #define BT_UART_MSG_2_FRAME5BTMINRSSI_POS (0)
3620 #define BT_UART_MSG_2_FRAME5BTMINRSSI_MSK \
3621 (0xF<<BT_UART_MSG_2_FRAME5BTMINRSSI_POS)
3622 #define BT_UART_MSG_2_FRAME5LESCANINITMODE_POS (4)
3623 #define BT_UART_MSG_2_FRAME5LESCANINITMODE_MSK \
3624 (0x1<<BT_UART_MSG_2_FRAME5LESCANINITMODE_POS)
3625 #define BT_UART_MSG_2_FRAME5LEADVERMODE_POS (5)
3626 #define BT_UART_MSG_2_FRAME5LEADVERMODE_MSK \
3627 (0x1<<BT_UART_MSG_2_FRAME5LEADVERMODE_POS)
3628 #define BT_UART_MSG_2_FRAME5RESERVED_POS (6)
3629 #define BT_UART_MSG_2_FRAME5RESERVED_MSK \
3630 (0x3<<BT_UART_MSG_2_FRAME5RESERVED_POS)
3632 #define BT_UART_MSG_2_FRAME6LECONNINTERVAL_POS (0)
3633 #define BT_UART_MSG_2_FRAME6LECONNINTERVAL_MSK \
3634 (0x1F<<BT_UART_MSG_2_FRAME6LECONNINTERVAL_POS)
3635 #define BT_UART_MSG_2_FRAME6RFU_POS (5)
3636 #define BT_UART_MSG_2_FRAME6RFU_MSK \
3637 (0x1<<BT_UART_MSG_2_FRAME6RFU_POS)
3638 #define BT_UART_MSG_2_FRAME6RESERVED_POS (6)
3639 #define BT_UART_MSG_2_FRAME6RESERVED_MSK \
3640 (0x3<<BT_UART_MSG_2_FRAME6RESERVED_POS)
3642 #define BT_UART_MSG_2_FRAME7LECONNSLAVELAT_POS (0)
3643 #define BT_UART_MSG_2_FRAME7LECONNSLAVELAT_MSK \
3644 (0x7<<BT_UART_MSG_2_FRAME7LECONNSLAVELAT_POS)
3645 #define BT_UART_MSG_2_FRAME7LEPROFILE1_POS (3)
3646 #define BT_UART_MSG_2_FRAME7LEPROFILE1_MSK \
3647 (0x1<<BT_UART_MSG_2_FRAME7LEPROFILE1_POS)
3648 #define BT_UART_MSG_2_FRAME7LEPROFILE2_POS (4)
3649 #define BT_UART_MSG_2_FRAME7LEPROFILE2_MSK \
3650 (0x1<<BT_UART_MSG_2_FRAME7LEPROFILE2_POS)
3651 #define BT_UART_MSG_2_FRAME7LEPROFILEOTHER_POS (5)
3652 #define BT_UART_MSG_2_FRAME7LEPROFILEOTHER_MSK \
3653 (0x1<<BT_UART_MSG_2_FRAME7LEPROFILEOTHER_POS)
3654 #define BT_UART_MSG_2_FRAME7RESERVED_POS (6)
3655 #define BT_UART_MSG_2_FRAME7RESERVED_MSK \
3656 (0x3<<BT_UART_MSG_2_FRAME7RESERVED_POS)
3659 #define BT_ENABLE_REDUCED_TXPOWER_THRESHOLD (-62)
3660 #define BT_DISABLE_REDUCED_TXPOWER_THRESHOLD (-65)
3662 struct iwl_bt_uart_msg {
3673 struct iwl_bt_coex_profile_notif {
3674 struct iwl_bt_uart_msg last_bt_uart_msg;
3675 u8 bt_status; /* 0 - off, 1 - on */
3676 u8 bt_traffic_load; /* 0 .. 3? */
3677 u8 bt_ci_compliance; /* 0 - not complied, 1 - complied */
3681 #define IWL_BT_COEX_PRIO_TBL_SHARED_ANTENNA_POS 0
3682 #define IWL_BT_COEX_PRIO_TBL_SHARED_ANTENNA_MSK 0x1
3683 #define IWL_BT_COEX_PRIO_TBL_PRIO_POS 1
3684 #define IWL_BT_COEX_PRIO_TBL_PRIO_MASK 0x0e
3685 #define IWL_BT_COEX_PRIO_TBL_RESERVED_POS 4
3686 #define IWL_BT_COEX_PRIO_TBL_RESERVED_MASK 0xf0
3687 #define IWL_BT_COEX_PRIO_TBL_PRIO_SHIFT 1
3690 * BT Coexistence Priority table
3691 * REPLY_BT_COEX_PRIO_TABLE = 0xcc
3693 enum bt_coex_prio_table_events {
3694 BT_COEX_PRIO_TBL_EVT_INIT_CALIB1 = 0,
3695 BT_COEX_PRIO_TBL_EVT_INIT_CALIB2 = 1,
3696 BT_COEX_PRIO_TBL_EVT_PERIODIC_CALIB_LOW1 = 2,
3697 BT_COEX_PRIO_TBL_EVT_PERIODIC_CALIB_LOW2 = 3, /* DC calib */
3698 BT_COEX_PRIO_TBL_EVT_PERIODIC_CALIB_HIGH1 = 4,
3699 BT_COEX_PRIO_TBL_EVT_PERIODIC_CALIB_HIGH2 = 5,
3700 BT_COEX_PRIO_TBL_EVT_DTIM = 6,
3701 BT_COEX_PRIO_TBL_EVT_SCAN52 = 7,
3702 BT_COEX_PRIO_TBL_EVT_SCAN24 = 8,
3703 BT_COEX_PRIO_TBL_EVT_RESERVED0 = 9,
3704 BT_COEX_PRIO_TBL_EVT_RESERVED1 = 10,
3705 BT_COEX_PRIO_TBL_EVT_RESERVED2 = 11,
3706 BT_COEX_PRIO_TBL_EVT_RESERVED3 = 12,
3707 BT_COEX_PRIO_TBL_EVT_RESERVED4 = 13,
3708 BT_COEX_PRIO_TBL_EVT_RESERVED5 = 14,
3709 BT_COEX_PRIO_TBL_EVT_RESERVED6 = 15,
3710 /* BT_COEX_PRIO_TBL_EVT_MAX should always be last */
3711 BT_COEX_PRIO_TBL_EVT_MAX,
3714 enum bt_coex_prio_table_priorities {
3715 BT_COEX_PRIO_TBL_DISABLED = 0,
3716 BT_COEX_PRIO_TBL_PRIO_LOW = 1,
3717 BT_COEX_PRIO_TBL_PRIO_HIGH = 2,
3718 BT_COEX_PRIO_TBL_PRIO_BYPASS = 3,
3719 BT_COEX_PRIO_TBL_PRIO_COEX_OFF = 4,
3720 BT_COEX_PRIO_TBL_PRIO_COEX_ON = 5,
3721 BT_COEX_PRIO_TBL_PRIO_RSRVD1 = 6,
3722 BT_COEX_PRIO_TBL_PRIO_RSRVD2 = 7,
3723 BT_COEX_PRIO_TBL_MAX,
3726 struct iwl_bt_coex_prio_table_cmd {
3727 u8 prio_tbl[BT_COEX_PRIO_TBL_EVT_MAX];
3730 #define IWL_BT_COEX_ENV_CLOSE 0
3731 #define IWL_BT_COEX_ENV_OPEN 1
3733 * BT Protection Envelope
3734 * REPLY_BT_COEX_PROT_ENV = 0xcd
3736 struct iwl_bt_coex_prot_env_cmd {
3737 u8 action; /* 0 = closed, 1 = open */
3738 u8 type; /* 0 .. 15 */
3745 enum iwlagn_d3_wakeup_filters {
3746 IWLAGN_D3_WAKEUP_RFKILL = BIT(0),
3747 IWLAGN_D3_WAKEUP_SYSASSERT = BIT(1),
3750 struct iwlagn_d3_config_cmd {
3751 __le32 min_sleep_time;
3752 __le32 wakeup_flags;
3756 * REPLY_WOWLAN_PATTERNS
3758 #define IWLAGN_WOWLAN_MIN_PATTERN_LEN 16
3759 #define IWLAGN_WOWLAN_MAX_PATTERN_LEN 128
3761 struct iwlagn_wowlan_pattern {
3762 u8 mask[IWLAGN_WOWLAN_MAX_PATTERN_LEN / 8];
3763 u8 pattern[IWLAGN_WOWLAN_MAX_PATTERN_LEN];
3769 #define IWLAGN_WOWLAN_MAX_PATTERNS 20
3771 struct iwlagn_wowlan_patterns_cmd {
3773 struct iwlagn_wowlan_pattern patterns[];
3777 * REPLY_WOWLAN_WAKEUP_FILTER
3779 enum iwlagn_wowlan_wakeup_filters {
3780 IWLAGN_WOWLAN_WAKEUP_MAGIC_PACKET = BIT(0),
3781 IWLAGN_WOWLAN_WAKEUP_PATTERN_MATCH = BIT(1),
3782 IWLAGN_WOWLAN_WAKEUP_BEACON_MISS = BIT(2),
3783 IWLAGN_WOWLAN_WAKEUP_LINK_CHANGE = BIT(3),
3784 IWLAGN_WOWLAN_WAKEUP_GTK_REKEY_FAIL = BIT(4),
3785 IWLAGN_WOWLAN_WAKEUP_EAP_IDENT_REQ = BIT(5),
3786 IWLAGN_WOWLAN_WAKEUP_4WAY_HANDSHAKE = BIT(6),
3787 IWLAGN_WOWLAN_WAKEUP_ALWAYS = BIT(7),
3788 IWLAGN_WOWLAN_WAKEUP_ENABLE_NET_DETECT = BIT(8),
3791 struct iwlagn_wowlan_wakeup_filter_cmd {
3799 * REPLY_WOWLAN_TSC_RSC_PARAMS
3801 #define IWLAGN_NUM_RSC 16
3809 struct iwlagn_tkip_rsc_tsc {
3810 struct tkip_sc unicast_rsc[IWLAGN_NUM_RSC];
3811 struct tkip_sc multicast_rsc[IWLAGN_NUM_RSC];
3819 struct iwlagn_aes_rsc_tsc {
3820 struct aes_sc unicast_rsc[IWLAGN_NUM_RSC];
3821 struct aes_sc multicast_rsc[IWLAGN_NUM_RSC];
3825 union iwlagn_all_tsc_rsc {
3826 struct iwlagn_tkip_rsc_tsc tkip;
3827 struct iwlagn_aes_rsc_tsc aes;
3830 struct iwlagn_wowlan_rsc_tsc_params_cmd {
3831 union iwlagn_all_tsc_rsc all_tsc_rsc;
3835 * REPLY_WOWLAN_TKIP_PARAMS
3837 #define IWLAGN_MIC_KEY_SIZE 8
3838 #define IWLAGN_P1K_SIZE 5
3839 struct iwlagn_mic_keys {
3840 u8 tx[IWLAGN_MIC_KEY_SIZE];
3841 u8 rx_unicast[IWLAGN_MIC_KEY_SIZE];
3842 u8 rx_mcast[IWLAGN_MIC_KEY_SIZE];
3845 struct iwlagn_p1k_cache {
3846 __le16 p1k[IWLAGN_P1K_SIZE];
3849 #define IWLAGN_NUM_RX_P1K_CACHE 2
3851 struct iwlagn_wowlan_tkip_params_cmd {
3852 struct iwlagn_mic_keys mic_keys;
3853 struct iwlagn_p1k_cache tx;
3854 struct iwlagn_p1k_cache rx_uni[IWLAGN_NUM_RX_P1K_CACHE];
3855 struct iwlagn_p1k_cache rx_multi[IWLAGN_NUM_RX_P1K_CACHE];
3859 * REPLY_WOWLAN_KEK_KCK_MATERIAL
3862 #define IWLAGN_KCK_MAX_SIZE 32
3863 #define IWLAGN_KEK_MAX_SIZE 32
3865 struct iwlagn_wowlan_kek_kck_material_cmd {
3866 u8 kck[IWLAGN_KCK_MAX_SIZE];
3867 u8 kek[IWLAGN_KEK_MAX_SIZE];
3873 #define RF_KILL_INDICATOR_FOR_WOWLAN 0x87
3876 * REPLY_WOWLAN_GET_STATUS = 0xe5
3878 struct iwlagn_wowlan_status {
3880 __le32 rekey_status;
3881 __le32 wakeup_reason;
3884 __le16 qos_seq_ctr[8];
3885 __le16 non_qos_seq_ctr;
3887 union iwlagn_all_tsc_rsc tsc_rsc;
3892 * REPLY_WIPAN_PARAMS = 0xb2 (Commands and Notification)
3896 * Minimum slot time in TU
3898 #define IWL_MIN_SLOT_TIME 20
3901 * struct iwl_wipan_slot
3902 * @width: Time in TU
3907 struct iwl_wipan_slot {
3913 #define IWL_WIPAN_PARAMS_FLG_LEAVE_CHANNEL_CTS BIT(1) /* reserved */
3914 #define IWL_WIPAN_PARAMS_FLG_LEAVE_CHANNEL_QUIET BIT(2) /* reserved */
3915 #define IWL_WIPAN_PARAMS_FLG_SLOTTED_MODE BIT(3) /* reserved */
3916 #define IWL_WIPAN_PARAMS_FLG_FILTER_BEACON_NOTIF BIT(4)
3917 #define IWL_WIPAN_PARAMS_FLG_FULL_SLOTTED_MODE BIT(5)
3920 * struct iwl_wipan_params_cmd
3923 * bit1: CP leave channel with CTS
3924 * bit2: CP leave channel qith Quiet
3925 * bit3: slotted mode
3926 * 1 - work in slotted mode
3927 * 0 - work in non slotted mode
3928 * bit4: filter beacon notification
3929 * bit5: full tx slotted mode. if this flag is set,
3930 * uCode will perform leaving channel methods in context switch
3931 * also when working in same channel mode
3932 * @num_slots: 1 - 10
3934 struct iwl_wipan_params_cmd {
3938 struct iwl_wipan_slot slots[10];
3942 * REPLY_WIPAN_P2P_CHANNEL_SWITCH = 0xb9
3944 * TODO: Figure out what this is used for,
3945 * it can only switch between 2.4 GHz
3949 struct iwl_wipan_p2p_channel_switch_cmd {
3955 * REPLY_WIPAN_NOA_NOTIFICATION = 0xbc
3957 * This is used by the device to notify us of the
3958 * NoA schedule it determined so we can forward it
3959 * to userspace for inclusion in probe responses.
3961 * In beacons, the NoA schedule is simply appended
3962 * to the frame we give the device.
3965 struct iwl_wipan_noa_descriptor {
3972 struct iwl_wipan_noa_attribute {
3977 struct iwl_wipan_noa_descriptor descr0, descr1;
3981 struct iwl_wipan_noa_notification {
3983 struct iwl_wipan_noa_attribute noa_attribute;
3986 #endif /* __iwl_commands_h__ */