GNU Linux-libre 4.19.286-gnu1
[releases.git] / drivers / thermal / rockchip_thermal.c
1 /*
2  * Copyright (c) 2014-2016, Fuzhou Rockchip Electronics Co., Ltd
3  * Caesar Wang <wxt@rock-chips.com>
4  *
5  * This program is free software; you can redistribute it and/or modify it
6  * under the terms and conditions of the GNU General Public License,
7  * version 2, as published by the Free Software Foundation.
8  *
9  * This program is distributed in the hope it will be useful, but WITHOUT
10  * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
11  * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
12  * more details.
13  */
14
15 #include <linux/clk.h>
16 #include <linux/delay.h>
17 #include <linux/interrupt.h>
18 #include <linux/io.h>
19 #include <linux/module.h>
20 #include <linux/of.h>
21 #include <linux/of_address.h>
22 #include <linux/of_irq.h>
23 #include <linux/platform_device.h>
24 #include <linux/regmap.h>
25 #include <linux/reset.h>
26 #include <linux/thermal.h>
27 #include <linux/mfd/syscon.h>
28 #include <linux/pinctrl/consumer.h>
29
30 /**
31  * If the temperature over a period of time High,
32  * the resulting TSHUT gave CRU module,let it reset the entire chip,
33  * or via GPIO give PMIC.
34  */
35 enum tshut_mode {
36         TSHUT_MODE_CRU = 0,
37         TSHUT_MODE_GPIO,
38 };
39
40 /**
41  * The system Temperature Sensors tshut(tshut) polarity
42  * the bit 8 is tshut polarity.
43  * 0: low active, 1: high active
44  */
45 enum tshut_polarity {
46         TSHUT_LOW_ACTIVE = 0,
47         TSHUT_HIGH_ACTIVE,
48 };
49
50 /**
51  * The system has two Temperature Sensors.
52  * sensor0 is for CPU, and sensor1 is for GPU.
53  */
54 enum sensor_id {
55         SENSOR_CPU = 0,
56         SENSOR_GPU,
57 };
58
59 /**
60  * The conversion table has the adc value and temperature.
61  * ADC_DECREMENT: the adc value is of diminishing.(e.g. rk3288_code_table)
62  * ADC_INCREMENT: the adc value is incremental.(e.g. rk3368_code_table)
63  */
64 enum adc_sort_mode {
65         ADC_DECREMENT = 0,
66         ADC_INCREMENT,
67 };
68
69 /**
70  * The max sensors is two in rockchip SoCs.
71  * Two sensors: CPU and GPU sensor.
72  */
73 #define SOC_MAX_SENSORS 2
74
75 /**
76  * struct chip_tsadc_table - hold information about chip-specific differences
77  * @id: conversion table
78  * @length: size of conversion table
79  * @data_mask: mask to apply on data inputs
80  * @mode: sort mode of this adc variant (incrementing or decrementing)
81  */
82 struct chip_tsadc_table {
83         const struct tsadc_table *id;
84         unsigned int length;
85         u32 data_mask;
86         enum adc_sort_mode mode;
87 };
88
89 /**
90  * struct rockchip_tsadc_chip - hold the private data of tsadc chip
91  * @chn_id[SOC_MAX_SENSORS]: the sensor id of chip correspond to the channel
92  * @chn_num: the channel number of tsadc chip
93  * @tshut_temp: the hardware-controlled shutdown temperature value
94  * @tshut_mode: the hardware-controlled shutdown mode (0:CRU 1:GPIO)
95  * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH)
96  * @initialize: SoC special initialize tsadc controller method
97  * @irq_ack: clear the interrupt
98  * @get_temp: get the temperature
99  * @set_alarm_temp: set the high temperature interrupt
100  * @set_tshut_temp: set the hardware-controlled shutdown temperature
101  * @set_tshut_mode: set the hardware-controlled shutdown mode
102  * @table: the chip-specific conversion table
103  */
104 struct rockchip_tsadc_chip {
105         /* The sensor id of chip correspond to the ADC channel */
106         int chn_id[SOC_MAX_SENSORS];
107         int chn_num;
108
109         /* The hardware-controlled tshut property */
110         int tshut_temp;
111         enum tshut_mode tshut_mode;
112         enum tshut_polarity tshut_polarity;
113
114         /* Chip-wide methods */
115         void (*initialize)(struct regmap *grf,
116                            void __iomem *reg, enum tshut_polarity p);
117         void (*irq_ack)(void __iomem *reg);
118         void (*control)(void __iomem *reg, bool on);
119
120         /* Per-sensor methods */
121         int (*get_temp)(const struct chip_tsadc_table *table,
122                         int chn, void __iomem *reg, int *temp);
123         int (*set_alarm_temp)(const struct chip_tsadc_table *table,
124                               int chn, void __iomem *reg, int temp);
125         int (*set_tshut_temp)(const struct chip_tsadc_table *table,
126                               int chn, void __iomem *reg, int temp);
127         void (*set_tshut_mode)(int chn, void __iomem *reg, enum tshut_mode m);
128
129         /* Per-table methods */
130         struct chip_tsadc_table table;
131 };
132
133 /**
134  * struct rockchip_thermal_sensor - hold the information of thermal sensor
135  * @thermal:  pointer to the platform/configuration data
136  * @tzd: pointer to a thermal zone
137  * @id: identifier of the thermal sensor
138  */
139 struct rockchip_thermal_sensor {
140         struct rockchip_thermal_data *thermal;
141         struct thermal_zone_device *tzd;
142         int id;
143 };
144
145 /**
146  * struct rockchip_thermal_data - hold the private data of thermal driver
147  * @chip: pointer to the platform/configuration data
148  * @pdev: platform device of thermal
149  * @reset: the reset controller of tsadc
150  * @sensors[SOC_MAX_SENSORS]: the thermal sensor
151  * @clk: the controller clock is divided by the exteral 24MHz
152  * @pclk: the advanced peripherals bus clock
153  * @grf: the general register file will be used to do static set by software
154  * @regs: the base address of tsadc controller
155  * @tshut_temp: the hardware-controlled shutdown temperature value
156  * @tshut_mode: the hardware-controlled shutdown mode (0:CRU 1:GPIO)
157  * @tshut_polarity: the hardware-controlled active polarity (0:LOW 1:HIGH)
158  */
159 struct rockchip_thermal_data {
160         const struct rockchip_tsadc_chip *chip;
161         struct platform_device *pdev;
162         struct reset_control *reset;
163
164         struct rockchip_thermal_sensor sensors[SOC_MAX_SENSORS];
165
166         struct clk *clk;
167         struct clk *pclk;
168
169         struct regmap *grf;
170         void __iomem *regs;
171
172         int tshut_temp;
173         enum tshut_mode tshut_mode;
174         enum tshut_polarity tshut_polarity;
175 };
176
177 /**
178  * TSADC Sensor Register description:
179  *
180  * TSADCV2_* are used for RK3288 SoCs, the other chips can reuse it.
181  * TSADCV3_* are used for newer SoCs than RK3288. (e.g: RK3228, RK3399)
182  *
183  */
184 #define TSADCV2_USER_CON                        0x00
185 #define TSADCV2_AUTO_CON                        0x04
186 #define TSADCV2_INT_EN                          0x08
187 #define TSADCV2_INT_PD                          0x0c
188 #define TSADCV2_DATA(chn)                       (0x20 + (chn) * 0x04)
189 #define TSADCV2_COMP_INT(chn)                   (0x30 + (chn) * 0x04)
190 #define TSADCV2_COMP_SHUT(chn)                  (0x40 + (chn) * 0x04)
191 #define TSADCV2_HIGHT_INT_DEBOUNCE              0x60
192 #define TSADCV2_HIGHT_TSHUT_DEBOUNCE            0x64
193 #define TSADCV2_AUTO_PERIOD                     0x68
194 #define TSADCV2_AUTO_PERIOD_HT                  0x6c
195
196 #define TSADCV2_AUTO_EN                         BIT(0)
197 #define TSADCV2_AUTO_SRC_EN(chn)                BIT(4 + (chn))
198 #define TSADCV2_AUTO_TSHUT_POLARITY_HIGH        BIT(8)
199
200 #define TSADCV3_AUTO_Q_SEL_EN                   BIT(1)
201
202 #define TSADCV2_INT_SRC_EN(chn)                 BIT(chn)
203 #define TSADCV2_SHUT_2GPIO_SRC_EN(chn)          BIT(4 + (chn))
204 #define TSADCV2_SHUT_2CRU_SRC_EN(chn)           BIT(8 + (chn))
205
206 #define TSADCV2_INT_PD_CLEAR_MASK               ~BIT(8)
207 #define TSADCV3_INT_PD_CLEAR_MASK               ~BIT(16)
208
209 #define TSADCV2_DATA_MASK                       0xfff
210 #define TSADCV3_DATA_MASK                       0x3ff
211
212 #define TSADCV2_HIGHT_INT_DEBOUNCE_COUNT        4
213 #define TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT      4
214 #define TSADCV2_AUTO_PERIOD_TIME                250 /* 250ms */
215 #define TSADCV2_AUTO_PERIOD_HT_TIME             50  /* 50ms */
216 #define TSADCV3_AUTO_PERIOD_TIME                1875 /* 2.5ms */
217 #define TSADCV3_AUTO_PERIOD_HT_TIME             1875 /* 2.5ms */
218
219 #define TSADCV2_USER_INTER_PD_SOC               0x340 /* 13 clocks */
220
221 #define GRF_SARADC_TESTBIT                      0x0e644
222 #define GRF_TSADC_TESTBIT_L                     0x0e648
223 #define GRF_TSADC_TESTBIT_H                     0x0e64c
224
225 #define GRF_SARADC_TESTBIT_ON                   (0x10001 << 2)
226 #define GRF_TSADC_TESTBIT_H_ON                  (0x10001 << 2)
227 #define GRF_TSADC_VCM_EN_L                      (0x10001 << 7)
228 #define GRF_TSADC_VCM_EN_H                      (0x10001 << 7)
229
230 /**
231  * struct tsadc_table - code to temperature conversion table
232  * @code: the value of adc channel
233  * @temp: the temperature
234  * Note:
235  * code to temperature mapping of the temperature sensor is a piece wise linear
236  * curve.Any temperature, code faling between to 2 give temperatures can be
237  * linearly interpolated.
238  * Code to Temperature mapping should be updated based on manufacturer results.
239  */
240 struct tsadc_table {
241         u32 code;
242         int temp;
243 };
244
245 static const struct tsadc_table rv1108_table[] = {
246         {0, -40000},
247         {374, -40000},
248         {382, -35000},
249         {389, -30000},
250         {397, -25000},
251         {405, -20000},
252         {413, -15000},
253         {421, -10000},
254         {429, -5000},
255         {436, 0},
256         {444, 5000},
257         {452, 10000},
258         {460, 15000},
259         {468, 20000},
260         {476, 25000},
261         {483, 30000},
262         {491, 35000},
263         {499, 40000},
264         {507, 45000},
265         {515, 50000},
266         {523, 55000},
267         {531, 60000},
268         {539, 65000},
269         {547, 70000},
270         {555, 75000},
271         {562, 80000},
272         {570, 85000},
273         {578, 90000},
274         {586, 95000},
275         {594, 100000},
276         {602, 105000},
277         {610, 110000},
278         {618, 115000},
279         {626, 120000},
280         {634, 125000},
281         {TSADCV2_DATA_MASK, 125000},
282 };
283
284 static const struct tsadc_table rk3228_code_table[] = {
285         {0, -40000},
286         {588, -40000},
287         {593, -35000},
288         {598, -30000},
289         {603, -25000},
290         {608, -20000},
291         {613, -15000},
292         {618, -10000},
293         {623, -5000},
294         {629, 0},
295         {634, 5000},
296         {639, 10000},
297         {644, 15000},
298         {649, 20000},
299         {654, 25000},
300         {660, 30000},
301         {665, 35000},
302         {670, 40000},
303         {675, 45000},
304         {681, 50000},
305         {686, 55000},
306         {691, 60000},
307         {696, 65000},
308         {702, 70000},
309         {707, 75000},
310         {712, 80000},
311         {717, 85000},
312         {723, 90000},
313         {728, 95000},
314         {733, 100000},
315         {738, 105000},
316         {744, 110000},
317         {749, 115000},
318         {754, 120000},
319         {760, 125000},
320         {TSADCV2_DATA_MASK, 125000},
321 };
322
323 static const struct tsadc_table rk3288_code_table[] = {
324         {TSADCV2_DATA_MASK, -40000},
325         {3800, -40000},
326         {3792, -35000},
327         {3783, -30000},
328         {3774, -25000},
329         {3765, -20000},
330         {3756, -15000},
331         {3747, -10000},
332         {3737, -5000},
333         {3728, 0},
334         {3718, 5000},
335         {3708, 10000},
336         {3698, 15000},
337         {3688, 20000},
338         {3678, 25000},
339         {3667, 30000},
340         {3656, 35000},
341         {3645, 40000},
342         {3634, 45000},
343         {3623, 50000},
344         {3611, 55000},
345         {3600, 60000},
346         {3588, 65000},
347         {3575, 70000},
348         {3563, 75000},
349         {3550, 80000},
350         {3537, 85000},
351         {3524, 90000},
352         {3510, 95000},
353         {3496, 100000},
354         {3482, 105000},
355         {3467, 110000},
356         {3452, 115000},
357         {3437, 120000},
358         {3421, 125000},
359         {0, 125000},
360 };
361
362 static const struct tsadc_table rk3328_code_table[] = {
363         {0, -40000},
364         {296, -40000},
365         {304, -35000},
366         {313, -30000},
367         {331, -20000},
368         {340, -15000},
369         {349, -10000},
370         {359, -5000},
371         {368, 0},
372         {378, 5000},
373         {388, 10000},
374         {398, 15000},
375         {408, 20000},
376         {418, 25000},
377         {429, 30000},
378         {440, 35000},
379         {451, 40000},
380         {462, 45000},
381         {473, 50000},
382         {485, 55000},
383         {496, 60000},
384         {508, 65000},
385         {521, 70000},
386         {533, 75000},
387         {546, 80000},
388         {559, 85000},
389         {572, 90000},
390         {586, 95000},
391         {600, 100000},
392         {614, 105000},
393         {629, 110000},
394         {644, 115000},
395         {659, 120000},
396         {675, 125000},
397         {TSADCV2_DATA_MASK, 125000},
398 };
399
400 static const struct tsadc_table rk3368_code_table[] = {
401         {0, -40000},
402         {106, -40000},
403         {108, -35000},
404         {110, -30000},
405         {112, -25000},
406         {114, -20000},
407         {116, -15000},
408         {118, -10000},
409         {120, -5000},
410         {122, 0},
411         {124, 5000},
412         {126, 10000},
413         {128, 15000},
414         {130, 20000},
415         {132, 25000},
416         {134, 30000},
417         {136, 35000},
418         {138, 40000},
419         {140, 45000},
420         {142, 50000},
421         {144, 55000},
422         {146, 60000},
423         {148, 65000},
424         {150, 70000},
425         {152, 75000},
426         {154, 80000},
427         {156, 85000},
428         {158, 90000},
429         {160, 95000},
430         {162, 100000},
431         {163, 105000},
432         {165, 110000},
433         {167, 115000},
434         {169, 120000},
435         {171, 125000},
436         {TSADCV3_DATA_MASK, 125000},
437 };
438
439 static const struct tsadc_table rk3399_code_table[] = {
440         {0, -40000},
441         {402, -40000},
442         {410, -35000},
443         {419, -30000},
444         {427, -25000},
445         {436, -20000},
446         {444, -15000},
447         {453, -10000},
448         {461, -5000},
449         {470, 0},
450         {478, 5000},
451         {487, 10000},
452         {496, 15000},
453         {504, 20000},
454         {513, 25000},
455         {521, 30000},
456         {530, 35000},
457         {538, 40000},
458         {547, 45000},
459         {555, 50000},
460         {564, 55000},
461         {573, 60000},
462         {581, 65000},
463         {590, 70000},
464         {599, 75000},
465         {607, 80000},
466         {616, 85000},
467         {624, 90000},
468         {633, 95000},
469         {642, 100000},
470         {650, 105000},
471         {659, 110000},
472         {668, 115000},
473         {677, 120000},
474         {685, 125000},
475         {TSADCV3_DATA_MASK, 125000},
476 };
477
478 static u32 rk_tsadcv2_temp_to_code(const struct chip_tsadc_table *table,
479                                    int temp)
480 {
481         int high, low, mid;
482         unsigned long num;
483         unsigned int denom;
484         u32 error = table->data_mask;
485
486         low = 0;
487         high = (table->length - 1) - 1; /* ignore the last check for table */
488         mid = (high + low) / 2;
489
490         /* Return mask code data when the temp is over table range */
491         if (temp < table->id[low].temp || temp > table->id[high].temp)
492                 goto exit;
493
494         while (low <= high) {
495                 if (temp == table->id[mid].temp)
496                         return table->id[mid].code;
497                 else if (temp < table->id[mid].temp)
498                         high = mid - 1;
499                 else
500                         low = mid + 1;
501                 mid = (low + high) / 2;
502         }
503
504         /*
505          * The conversion code granularity provided by the table. Let's
506          * assume that the relationship between temperature and
507          * analog value between 2 table entries is linear and interpolate
508          * to produce less granular result.
509          */
510         num = abs(table->id[mid + 1].code - table->id[mid].code);
511         num *= temp - table->id[mid].temp;
512         denom = table->id[mid + 1].temp - table->id[mid].temp;
513
514         switch (table->mode) {
515         case ADC_DECREMENT:
516                 return table->id[mid].code - (num / denom);
517         case ADC_INCREMENT:
518                 return table->id[mid].code + (num / denom);
519         default:
520                 pr_err("%s: unknown table mode: %d\n", __func__, table->mode);
521                 return error;
522         }
523
524 exit:
525         pr_err("%s: invalid temperature, temp=%d error=%d\n",
526                __func__, temp, error);
527         return error;
528 }
529
530 static int rk_tsadcv2_code_to_temp(const struct chip_tsadc_table *table,
531                                    u32 code, int *temp)
532 {
533         unsigned int low = 1;
534         unsigned int high = table->length - 1;
535         unsigned int mid = (low + high) / 2;
536         unsigned int num;
537         unsigned long denom;
538
539         WARN_ON(table->length < 2);
540
541         switch (table->mode) {
542         case ADC_DECREMENT:
543                 code &= table->data_mask;
544                 if (code <= table->id[high].code)
545                         return -EAGAIN;         /* Incorrect reading */
546
547                 while (low <= high) {
548                         if (code >= table->id[mid].code &&
549                             code < table->id[mid - 1].code)
550                                 break;
551                         else if (code < table->id[mid].code)
552                                 low = mid + 1;
553                         else
554                                 high = mid - 1;
555
556                         mid = (low + high) / 2;
557                 }
558                 break;
559         case ADC_INCREMENT:
560                 code &= table->data_mask;
561                 if (code < table->id[low].code)
562                         return -EAGAIN;         /* Incorrect reading */
563
564                 while (low <= high) {
565                         if (code <= table->id[mid].code &&
566                             code > table->id[mid - 1].code)
567                                 break;
568                         else if (code > table->id[mid].code)
569                                 low = mid + 1;
570                         else
571                                 high = mid - 1;
572
573                         mid = (low + high) / 2;
574                 }
575                 break;
576         default:
577                 pr_err("%s: unknown table mode: %d\n", __func__, table->mode);
578                 return -EINVAL;
579         }
580
581         /*
582          * The 5C granularity provided by the table is too much. Let's
583          * assume that the relationship between sensor readings and
584          * temperature between 2 table entries is linear and interpolate
585          * to produce less granular result.
586          */
587         num = table->id[mid].temp - table->id[mid - 1].temp;
588         num *= abs(table->id[mid - 1].code - code);
589         denom = abs(table->id[mid - 1].code - table->id[mid].code);
590         *temp = table->id[mid - 1].temp + (num / denom);
591
592         return 0;
593 }
594
595 /**
596  * rk_tsadcv2_initialize - initialize TASDC Controller.
597  *
598  * (1) Set TSADC_V2_AUTO_PERIOD:
599  *     Configure the interleave between every two accessing of
600  *     TSADC in normal operation.
601  *
602  * (2) Set TSADCV2_AUTO_PERIOD_HT:
603  *     Configure the interleave between every two accessing of
604  *     TSADC after the temperature is higher than COM_SHUT or COM_INT.
605  *
606  * (3) Set TSADCV2_HIGH_INT_DEBOUNCE and TSADC_HIGHT_TSHUT_DEBOUNCE:
607  *     If the temperature is higher than COMP_INT or COMP_SHUT for
608  *     "debounce" times, TSADC controller will generate interrupt or TSHUT.
609  */
610 static void rk_tsadcv2_initialize(struct regmap *grf, void __iomem *regs,
611                                   enum tshut_polarity tshut_polarity)
612 {
613         if (tshut_polarity == TSHUT_HIGH_ACTIVE)
614                 writel_relaxed(0U | TSADCV2_AUTO_TSHUT_POLARITY_HIGH,
615                                regs + TSADCV2_AUTO_CON);
616         else
617                 writel_relaxed(0U & ~TSADCV2_AUTO_TSHUT_POLARITY_HIGH,
618                                regs + TSADCV2_AUTO_CON);
619
620         writel_relaxed(TSADCV2_AUTO_PERIOD_TIME, regs + TSADCV2_AUTO_PERIOD);
621         writel_relaxed(TSADCV2_HIGHT_INT_DEBOUNCE_COUNT,
622                        regs + TSADCV2_HIGHT_INT_DEBOUNCE);
623         writel_relaxed(TSADCV2_AUTO_PERIOD_HT_TIME,
624                        regs + TSADCV2_AUTO_PERIOD_HT);
625         writel_relaxed(TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT,
626                        regs + TSADCV2_HIGHT_TSHUT_DEBOUNCE);
627 }
628
629 /**
630  * rk_tsadcv3_initialize - initialize TASDC Controller.
631  *
632  * (1) The tsadc control power sequence.
633  *
634  * (2) Set TSADC_V2_AUTO_PERIOD:
635  *     Configure the interleave between every two accessing of
636  *     TSADC in normal operation.
637  *
638  * (2) Set TSADCV2_AUTO_PERIOD_HT:
639  *     Configure the interleave between every two accessing of
640  *     TSADC after the temperature is higher than COM_SHUT or COM_INT.
641  *
642  * (3) Set TSADCV2_HIGH_INT_DEBOUNCE and TSADC_HIGHT_TSHUT_DEBOUNCE:
643  *     If the temperature is higher than COMP_INT or COMP_SHUT for
644  *     "debounce" times, TSADC controller will generate interrupt or TSHUT.
645  */
646 static void rk_tsadcv3_initialize(struct regmap *grf, void __iomem *regs,
647                                   enum tshut_polarity tshut_polarity)
648 {
649         /* The tsadc control power sequence */
650         if (IS_ERR(grf)) {
651                 /* Set interleave value to workround ic time sync issue */
652                 writel_relaxed(TSADCV2_USER_INTER_PD_SOC, regs +
653                                TSADCV2_USER_CON);
654
655                 writel_relaxed(TSADCV2_AUTO_PERIOD_TIME,
656                                regs + TSADCV2_AUTO_PERIOD);
657                 writel_relaxed(TSADCV2_HIGHT_INT_DEBOUNCE_COUNT,
658                                regs + TSADCV2_HIGHT_INT_DEBOUNCE);
659                 writel_relaxed(TSADCV2_AUTO_PERIOD_HT_TIME,
660                                regs + TSADCV2_AUTO_PERIOD_HT);
661                 writel_relaxed(TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT,
662                                regs + TSADCV2_HIGHT_TSHUT_DEBOUNCE);
663
664         } else {
665                 /* Enable the voltage common mode feature */
666                 regmap_write(grf, GRF_TSADC_TESTBIT_L, GRF_TSADC_VCM_EN_L);
667                 regmap_write(grf, GRF_TSADC_TESTBIT_H, GRF_TSADC_VCM_EN_H);
668
669                 usleep_range(15, 100); /* The spec note says at least 15 us */
670                 regmap_write(grf, GRF_SARADC_TESTBIT, GRF_SARADC_TESTBIT_ON);
671                 regmap_write(grf, GRF_TSADC_TESTBIT_H, GRF_TSADC_TESTBIT_H_ON);
672                 usleep_range(90, 200); /* The spec note says at least 90 us */
673
674                 writel_relaxed(TSADCV3_AUTO_PERIOD_TIME,
675                                regs + TSADCV2_AUTO_PERIOD);
676                 writel_relaxed(TSADCV2_HIGHT_INT_DEBOUNCE_COUNT,
677                                regs + TSADCV2_HIGHT_INT_DEBOUNCE);
678                 writel_relaxed(TSADCV3_AUTO_PERIOD_HT_TIME,
679                                regs + TSADCV2_AUTO_PERIOD_HT);
680                 writel_relaxed(TSADCV2_HIGHT_TSHUT_DEBOUNCE_COUNT,
681                                regs + TSADCV2_HIGHT_TSHUT_DEBOUNCE);
682         }
683
684         if (tshut_polarity == TSHUT_HIGH_ACTIVE)
685                 writel_relaxed(0U | TSADCV2_AUTO_TSHUT_POLARITY_HIGH,
686                                regs + TSADCV2_AUTO_CON);
687         else
688                 writel_relaxed(0U & ~TSADCV2_AUTO_TSHUT_POLARITY_HIGH,
689                                regs + TSADCV2_AUTO_CON);
690 }
691
692 static void rk_tsadcv2_irq_ack(void __iomem *regs)
693 {
694         u32 val;
695
696         val = readl_relaxed(regs + TSADCV2_INT_PD);
697         writel_relaxed(val & TSADCV2_INT_PD_CLEAR_MASK, regs + TSADCV2_INT_PD);
698 }
699
700 static void rk_tsadcv3_irq_ack(void __iomem *regs)
701 {
702         u32 val;
703
704         val = readl_relaxed(regs + TSADCV2_INT_PD);
705         writel_relaxed(val & TSADCV3_INT_PD_CLEAR_MASK, regs + TSADCV2_INT_PD);
706 }
707
708 static void rk_tsadcv2_control(void __iomem *regs, bool enable)
709 {
710         u32 val;
711
712         val = readl_relaxed(regs + TSADCV2_AUTO_CON);
713         if (enable)
714                 val |= TSADCV2_AUTO_EN;
715         else
716                 val &= ~TSADCV2_AUTO_EN;
717
718         writel_relaxed(val, regs + TSADCV2_AUTO_CON);
719 }
720
721 /**
722  * rk_tsadcv3_control - the tsadc controller is enabled or disabled.
723  *
724  * NOTE: TSADC controller works at auto mode, and some SoCs need set the
725  * tsadc_q_sel bit on TSADCV2_AUTO_CON[1]. The (1024 - tsadc_q) as output
726  * adc value if setting this bit to enable.
727  */
728 static void rk_tsadcv3_control(void __iomem *regs, bool enable)
729 {
730         u32 val;
731
732         val = readl_relaxed(regs + TSADCV2_AUTO_CON);
733         if (enable)
734                 val |= TSADCV2_AUTO_EN | TSADCV3_AUTO_Q_SEL_EN;
735         else
736                 val &= ~TSADCV2_AUTO_EN;
737
738         writel_relaxed(val, regs + TSADCV2_AUTO_CON);
739 }
740
741 static int rk_tsadcv2_get_temp(const struct chip_tsadc_table *table,
742                                int chn, void __iomem *regs, int *temp)
743 {
744         u32 val;
745
746         val = readl_relaxed(regs + TSADCV2_DATA(chn));
747
748         return rk_tsadcv2_code_to_temp(table, val, temp);
749 }
750
751 static int rk_tsadcv2_alarm_temp(const struct chip_tsadc_table *table,
752                                  int chn, void __iomem *regs, int temp)
753 {
754         u32 alarm_value;
755         u32 int_en, int_clr;
756
757         /*
758          * In some cases, some sensors didn't need the trip points, the
759          * set_trips will pass {-INT_MAX, INT_MAX} to trigger tsadc alarm
760          * in the end, ignore this case and disable the high temperature
761          * interrupt.
762          */
763         if (temp == INT_MAX) {
764                 int_clr = readl_relaxed(regs + TSADCV2_INT_EN);
765                 int_clr &= ~TSADCV2_INT_SRC_EN(chn);
766                 writel_relaxed(int_clr, regs + TSADCV2_INT_EN);
767                 return 0;
768         }
769
770         /* Make sure the value is valid */
771         alarm_value = rk_tsadcv2_temp_to_code(table, temp);
772         if (alarm_value == table->data_mask)
773                 return -ERANGE;
774
775         writel_relaxed(alarm_value & table->data_mask,
776                        regs + TSADCV2_COMP_INT(chn));
777
778         int_en = readl_relaxed(regs + TSADCV2_INT_EN);
779         int_en |= TSADCV2_INT_SRC_EN(chn);
780         writel_relaxed(int_en, regs + TSADCV2_INT_EN);
781
782         return 0;
783 }
784
785 static int rk_tsadcv2_tshut_temp(const struct chip_tsadc_table *table,
786                                  int chn, void __iomem *regs, int temp)
787 {
788         u32 tshut_value, val;
789
790         /* Make sure the value is valid */
791         tshut_value = rk_tsadcv2_temp_to_code(table, temp);
792         if (tshut_value == table->data_mask)
793                 return -ERANGE;
794
795         writel_relaxed(tshut_value, regs + TSADCV2_COMP_SHUT(chn));
796
797         /* TSHUT will be valid */
798         val = readl_relaxed(regs + TSADCV2_AUTO_CON);
799         writel_relaxed(val | TSADCV2_AUTO_SRC_EN(chn), regs + TSADCV2_AUTO_CON);
800
801         return 0;
802 }
803
804 static void rk_tsadcv2_tshut_mode(int chn, void __iomem *regs,
805                                   enum tshut_mode mode)
806 {
807         u32 val;
808
809         val = readl_relaxed(regs + TSADCV2_INT_EN);
810         if (mode == TSHUT_MODE_GPIO) {
811                 val &= ~TSADCV2_SHUT_2CRU_SRC_EN(chn);
812                 val |= TSADCV2_SHUT_2GPIO_SRC_EN(chn);
813         } else {
814                 val &= ~TSADCV2_SHUT_2GPIO_SRC_EN(chn);
815                 val |= TSADCV2_SHUT_2CRU_SRC_EN(chn);
816         }
817
818         writel_relaxed(val, regs + TSADCV2_INT_EN);
819 }
820
821 static const struct rockchip_tsadc_chip rv1108_tsadc_data = {
822         .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */
823         .chn_num = 1, /* one channel for tsadc */
824
825         .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
826         .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
827         .tshut_temp = 95000,
828
829         .initialize = rk_tsadcv2_initialize,
830         .irq_ack = rk_tsadcv3_irq_ack,
831         .control = rk_tsadcv3_control,
832         .get_temp = rk_tsadcv2_get_temp,
833         .set_alarm_temp = rk_tsadcv2_alarm_temp,
834         .set_tshut_temp = rk_tsadcv2_tshut_temp,
835         .set_tshut_mode = rk_tsadcv2_tshut_mode,
836
837         .table = {
838                 .id = rv1108_table,
839                 .length = ARRAY_SIZE(rv1108_table),
840                 .data_mask = TSADCV2_DATA_MASK,
841                 .mode = ADC_INCREMENT,
842         },
843 };
844
845 static const struct rockchip_tsadc_chip rk3228_tsadc_data = {
846         .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */
847         .chn_num = 1, /* one channel for tsadc */
848
849         .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
850         .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
851         .tshut_temp = 95000,
852
853         .initialize = rk_tsadcv2_initialize,
854         .irq_ack = rk_tsadcv3_irq_ack,
855         .control = rk_tsadcv3_control,
856         .get_temp = rk_tsadcv2_get_temp,
857         .set_alarm_temp = rk_tsadcv2_alarm_temp,
858         .set_tshut_temp = rk_tsadcv2_tshut_temp,
859         .set_tshut_mode = rk_tsadcv2_tshut_mode,
860
861         .table = {
862                 .id = rk3228_code_table,
863                 .length = ARRAY_SIZE(rk3228_code_table),
864                 .data_mask = TSADCV3_DATA_MASK,
865                 .mode = ADC_INCREMENT,
866         },
867 };
868
869 static const struct rockchip_tsadc_chip rk3288_tsadc_data = {
870         .chn_id[SENSOR_CPU] = 1, /* cpu sensor is channel 1 */
871         .chn_id[SENSOR_GPU] = 2, /* gpu sensor is channel 2 */
872         .chn_num = 2, /* two channels for tsadc */
873
874         .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
875         .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
876         .tshut_temp = 95000,
877
878         .initialize = rk_tsadcv2_initialize,
879         .irq_ack = rk_tsadcv2_irq_ack,
880         .control = rk_tsadcv2_control,
881         .get_temp = rk_tsadcv2_get_temp,
882         .set_alarm_temp = rk_tsadcv2_alarm_temp,
883         .set_tshut_temp = rk_tsadcv2_tshut_temp,
884         .set_tshut_mode = rk_tsadcv2_tshut_mode,
885
886         .table = {
887                 .id = rk3288_code_table,
888                 .length = ARRAY_SIZE(rk3288_code_table),
889                 .data_mask = TSADCV2_DATA_MASK,
890                 .mode = ADC_DECREMENT,
891         },
892 };
893
894 static const struct rockchip_tsadc_chip rk3328_tsadc_data = {
895         .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */
896         .chn_num = 1, /* one channels for tsadc */
897
898         .tshut_mode = TSHUT_MODE_CRU, /* default TSHUT via CRU */
899         .tshut_temp = 95000,
900
901         .initialize = rk_tsadcv2_initialize,
902         .irq_ack = rk_tsadcv3_irq_ack,
903         .control = rk_tsadcv3_control,
904         .get_temp = rk_tsadcv2_get_temp,
905         .set_alarm_temp = rk_tsadcv2_alarm_temp,
906         .set_tshut_temp = rk_tsadcv2_tshut_temp,
907         .set_tshut_mode = rk_tsadcv2_tshut_mode,
908
909         .table = {
910                 .id = rk3328_code_table,
911                 .length = ARRAY_SIZE(rk3328_code_table),
912                 .data_mask = TSADCV2_DATA_MASK,
913                 .mode = ADC_INCREMENT,
914         },
915 };
916
917 static const struct rockchip_tsadc_chip rk3366_tsadc_data = {
918         .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */
919         .chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */
920         .chn_num = 2, /* two channels for tsadc */
921
922         .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
923         .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
924         .tshut_temp = 95000,
925
926         .initialize = rk_tsadcv3_initialize,
927         .irq_ack = rk_tsadcv3_irq_ack,
928         .control = rk_tsadcv3_control,
929         .get_temp = rk_tsadcv2_get_temp,
930         .set_alarm_temp = rk_tsadcv2_alarm_temp,
931         .set_tshut_temp = rk_tsadcv2_tshut_temp,
932         .set_tshut_mode = rk_tsadcv2_tshut_mode,
933
934         .table = {
935                 .id = rk3228_code_table,
936                 .length = ARRAY_SIZE(rk3228_code_table),
937                 .data_mask = TSADCV3_DATA_MASK,
938                 .mode = ADC_INCREMENT,
939         },
940 };
941
942 static const struct rockchip_tsadc_chip rk3368_tsadc_data = {
943         .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */
944         .chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */
945         .chn_num = 2, /* two channels for tsadc */
946
947         .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
948         .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
949         .tshut_temp = 95000,
950
951         .initialize = rk_tsadcv2_initialize,
952         .irq_ack = rk_tsadcv2_irq_ack,
953         .control = rk_tsadcv2_control,
954         .get_temp = rk_tsadcv2_get_temp,
955         .set_alarm_temp = rk_tsadcv2_alarm_temp,
956         .set_tshut_temp = rk_tsadcv2_tshut_temp,
957         .set_tshut_mode = rk_tsadcv2_tshut_mode,
958
959         .table = {
960                 .id = rk3368_code_table,
961                 .length = ARRAY_SIZE(rk3368_code_table),
962                 .data_mask = TSADCV3_DATA_MASK,
963                 .mode = ADC_INCREMENT,
964         },
965 };
966
967 static const struct rockchip_tsadc_chip rk3399_tsadc_data = {
968         .chn_id[SENSOR_CPU] = 0, /* cpu sensor is channel 0 */
969         .chn_id[SENSOR_GPU] = 1, /* gpu sensor is channel 1 */
970         .chn_num = 2, /* two channels for tsadc */
971
972         .tshut_mode = TSHUT_MODE_GPIO, /* default TSHUT via GPIO give PMIC */
973         .tshut_polarity = TSHUT_LOW_ACTIVE, /* default TSHUT LOW ACTIVE */
974         .tshut_temp = 95000,
975
976         .initialize = rk_tsadcv3_initialize,
977         .irq_ack = rk_tsadcv3_irq_ack,
978         .control = rk_tsadcv3_control,
979         .get_temp = rk_tsadcv2_get_temp,
980         .set_alarm_temp = rk_tsadcv2_alarm_temp,
981         .set_tshut_temp = rk_tsadcv2_tshut_temp,
982         .set_tshut_mode = rk_tsadcv2_tshut_mode,
983
984         .table = {
985                 .id = rk3399_code_table,
986                 .length = ARRAY_SIZE(rk3399_code_table),
987                 .data_mask = TSADCV3_DATA_MASK,
988                 .mode = ADC_INCREMENT,
989         },
990 };
991
992 static const struct of_device_id of_rockchip_thermal_match[] = {
993         {
994                 .compatible = "rockchip,rv1108-tsadc",
995                 .data = (void *)&rv1108_tsadc_data,
996         },
997         {
998                 .compatible = "rockchip,rk3228-tsadc",
999                 .data = (void *)&rk3228_tsadc_data,
1000         },
1001         {
1002                 .compatible = "rockchip,rk3288-tsadc",
1003                 .data = (void *)&rk3288_tsadc_data,
1004         },
1005         {
1006                 .compatible = "rockchip,rk3328-tsadc",
1007                 .data = (void *)&rk3328_tsadc_data,
1008         },
1009         {
1010                 .compatible = "rockchip,rk3366-tsadc",
1011                 .data = (void *)&rk3366_tsadc_data,
1012         },
1013         {
1014                 .compatible = "rockchip,rk3368-tsadc",
1015                 .data = (void *)&rk3368_tsadc_data,
1016         },
1017         {
1018                 .compatible = "rockchip,rk3399-tsadc",
1019                 .data = (void *)&rk3399_tsadc_data,
1020         },
1021         { /* end */ },
1022 };
1023 MODULE_DEVICE_TABLE(of, of_rockchip_thermal_match);
1024
1025 static void
1026 rockchip_thermal_toggle_sensor(struct rockchip_thermal_sensor *sensor, bool on)
1027 {
1028         struct thermal_zone_device *tzd = sensor->tzd;
1029
1030         tzd->ops->set_mode(tzd,
1031                 on ? THERMAL_DEVICE_ENABLED : THERMAL_DEVICE_DISABLED);
1032 }
1033
1034 static irqreturn_t rockchip_thermal_alarm_irq_thread(int irq, void *dev)
1035 {
1036         struct rockchip_thermal_data *thermal = dev;
1037         int i;
1038
1039         dev_dbg(&thermal->pdev->dev, "thermal alarm\n");
1040
1041         thermal->chip->irq_ack(thermal->regs);
1042
1043         for (i = 0; i < thermal->chip->chn_num; i++)
1044                 thermal_zone_device_update(thermal->sensors[i].tzd,
1045                                            THERMAL_EVENT_UNSPECIFIED);
1046
1047         return IRQ_HANDLED;
1048 }
1049
1050 static int rockchip_thermal_set_trips(void *_sensor, int low, int high)
1051 {
1052         struct rockchip_thermal_sensor *sensor = _sensor;
1053         struct rockchip_thermal_data *thermal = sensor->thermal;
1054         const struct rockchip_tsadc_chip *tsadc = thermal->chip;
1055
1056         dev_dbg(&thermal->pdev->dev, "%s: sensor %d: low: %d, high %d\n",
1057                 __func__, sensor->id, low, high);
1058
1059         return tsadc->set_alarm_temp(&tsadc->table,
1060                                      sensor->id, thermal->regs, high);
1061 }
1062
1063 static int rockchip_thermal_get_temp(void *_sensor, int *out_temp)
1064 {
1065         struct rockchip_thermal_sensor *sensor = _sensor;
1066         struct rockchip_thermal_data *thermal = sensor->thermal;
1067         const struct rockchip_tsadc_chip *tsadc = sensor->thermal->chip;
1068         int retval;
1069
1070         retval = tsadc->get_temp(&tsadc->table,
1071                                  sensor->id, thermal->regs, out_temp);
1072         dev_dbg(&thermal->pdev->dev, "sensor %d - temp: %d, retval: %d\n",
1073                 sensor->id, *out_temp, retval);
1074
1075         return retval;
1076 }
1077
1078 static const struct thermal_zone_of_device_ops rockchip_of_thermal_ops = {
1079         .get_temp = rockchip_thermal_get_temp,
1080         .set_trips = rockchip_thermal_set_trips,
1081 };
1082
1083 static int rockchip_configure_from_dt(struct device *dev,
1084                                       struct device_node *np,
1085                                       struct rockchip_thermal_data *thermal)
1086 {
1087         u32 shut_temp, tshut_mode, tshut_polarity;
1088
1089         if (of_property_read_u32(np, "rockchip,hw-tshut-temp", &shut_temp)) {
1090                 dev_warn(dev,
1091                          "Missing tshut temp property, using default %d\n",
1092                          thermal->chip->tshut_temp);
1093                 thermal->tshut_temp = thermal->chip->tshut_temp;
1094         } else {
1095                 if (shut_temp > INT_MAX) {
1096                         dev_err(dev, "Invalid tshut temperature specified: %d\n",
1097                                 shut_temp);
1098                         return -ERANGE;
1099                 }
1100                 thermal->tshut_temp = shut_temp;
1101         }
1102
1103         if (of_property_read_u32(np, "rockchip,hw-tshut-mode", &tshut_mode)) {
1104                 dev_warn(dev,
1105                          "Missing tshut mode property, using default (%s)\n",
1106                          thermal->chip->tshut_mode == TSHUT_MODE_GPIO ?
1107                                 "gpio" : "cru");
1108                 thermal->tshut_mode = thermal->chip->tshut_mode;
1109         } else {
1110                 thermal->tshut_mode = tshut_mode;
1111         }
1112
1113         if (thermal->tshut_mode > 1) {
1114                 dev_err(dev, "Invalid tshut mode specified: %d\n",
1115                         thermal->tshut_mode);
1116                 return -EINVAL;
1117         }
1118
1119         if (of_property_read_u32(np, "rockchip,hw-tshut-polarity",
1120                                  &tshut_polarity)) {
1121                 dev_warn(dev,
1122                          "Missing tshut-polarity property, using default (%s)\n",
1123                          thermal->chip->tshut_polarity == TSHUT_LOW_ACTIVE ?
1124                                 "low" : "high");
1125                 thermal->tshut_polarity = thermal->chip->tshut_polarity;
1126         } else {
1127                 thermal->tshut_polarity = tshut_polarity;
1128         }
1129
1130         if (thermal->tshut_polarity > 1) {
1131                 dev_err(dev, "Invalid tshut-polarity specified: %d\n",
1132                         thermal->tshut_polarity);
1133                 return -EINVAL;
1134         }
1135
1136         /* The tsadc wont to handle the error in here since some SoCs didn't
1137          * need this property.
1138          */
1139         thermal->grf = syscon_regmap_lookup_by_phandle(np, "rockchip,grf");
1140         if (IS_ERR(thermal->grf))
1141                 dev_warn(dev, "Missing rockchip,grf property\n");
1142
1143         return 0;
1144 }
1145
1146 static int
1147 rockchip_thermal_register_sensor(struct platform_device *pdev,
1148                                  struct rockchip_thermal_data *thermal,
1149                                  struct rockchip_thermal_sensor *sensor,
1150                                  int id)
1151 {
1152         const struct rockchip_tsadc_chip *tsadc = thermal->chip;
1153         int error;
1154
1155         tsadc->set_tshut_mode(id, thermal->regs, thermal->tshut_mode);
1156
1157         error = tsadc->set_tshut_temp(&tsadc->table, id, thermal->regs,
1158                               thermal->tshut_temp);
1159         if (error)
1160                 dev_err(&pdev->dev, "%s: invalid tshut=%d, error=%d\n",
1161                         __func__, thermal->tshut_temp, error);
1162
1163         sensor->thermal = thermal;
1164         sensor->id = id;
1165         sensor->tzd = devm_thermal_zone_of_sensor_register(&pdev->dev, id,
1166                                         sensor, &rockchip_of_thermal_ops);
1167         if (IS_ERR(sensor->tzd)) {
1168                 error = PTR_ERR(sensor->tzd);
1169                 dev_err(&pdev->dev, "failed to register sensor %d: %d\n",
1170                         id, error);
1171                 return error;
1172         }
1173
1174         return 0;
1175 }
1176
1177 /**
1178  * Reset TSADC Controller, reset all tsadc registers.
1179  */
1180 static void rockchip_thermal_reset_controller(struct reset_control *reset)
1181 {
1182         reset_control_assert(reset);
1183         usleep_range(10, 20);
1184         reset_control_deassert(reset);
1185 }
1186
1187 static int rockchip_thermal_probe(struct platform_device *pdev)
1188 {
1189         struct device_node *np = pdev->dev.of_node;
1190         struct rockchip_thermal_data *thermal;
1191         const struct of_device_id *match;
1192         struct resource *res;
1193         int irq;
1194         int i;
1195         int error;
1196
1197         match = of_match_node(of_rockchip_thermal_match, np);
1198         if (!match)
1199                 return -ENXIO;
1200
1201         irq = platform_get_irq(pdev, 0);
1202         if (irq < 0) {
1203                 dev_err(&pdev->dev, "no irq resource?\n");
1204                 return -EINVAL;
1205         }
1206
1207         thermal = devm_kzalloc(&pdev->dev, sizeof(struct rockchip_thermal_data),
1208                                GFP_KERNEL);
1209         if (!thermal)
1210                 return -ENOMEM;
1211
1212         thermal->pdev = pdev;
1213
1214         thermal->chip = (const struct rockchip_tsadc_chip *)match->data;
1215         if (!thermal->chip)
1216                 return -EINVAL;
1217
1218         res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1219         thermal->regs = devm_ioremap_resource(&pdev->dev, res);
1220         if (IS_ERR(thermal->regs))
1221                 return PTR_ERR(thermal->regs);
1222
1223         thermal->reset = devm_reset_control_get(&pdev->dev, "tsadc-apb");
1224         if (IS_ERR(thermal->reset)) {
1225                 error = PTR_ERR(thermal->reset);
1226                 dev_err(&pdev->dev, "failed to get tsadc reset: %d\n", error);
1227                 return error;
1228         }
1229
1230         thermal->clk = devm_clk_get(&pdev->dev, "tsadc");
1231         if (IS_ERR(thermal->clk)) {
1232                 error = PTR_ERR(thermal->clk);
1233                 dev_err(&pdev->dev, "failed to get tsadc clock: %d\n", error);
1234                 return error;
1235         }
1236
1237         thermal->pclk = devm_clk_get(&pdev->dev, "apb_pclk");
1238         if (IS_ERR(thermal->pclk)) {
1239                 error = PTR_ERR(thermal->pclk);
1240                 dev_err(&pdev->dev, "failed to get apb_pclk clock: %d\n",
1241                         error);
1242                 return error;
1243         }
1244
1245         error = clk_prepare_enable(thermal->clk);
1246         if (error) {
1247                 dev_err(&pdev->dev, "failed to enable converter clock: %d\n",
1248                         error);
1249                 return error;
1250         }
1251
1252         error = clk_prepare_enable(thermal->pclk);
1253         if (error) {
1254                 dev_err(&pdev->dev, "failed to enable pclk: %d\n", error);
1255                 goto err_disable_clk;
1256         }
1257
1258         rockchip_thermal_reset_controller(thermal->reset);
1259
1260         error = rockchip_configure_from_dt(&pdev->dev, np, thermal);
1261         if (error) {
1262                 dev_err(&pdev->dev, "failed to parse device tree data: %d\n",
1263                         error);
1264                 goto err_disable_pclk;
1265         }
1266
1267         thermal->chip->initialize(thermal->grf, thermal->regs,
1268                                   thermal->tshut_polarity);
1269
1270         for (i = 0; i < thermal->chip->chn_num; i++) {
1271                 error = rockchip_thermal_register_sensor(pdev, thermal,
1272                                                 &thermal->sensors[i],
1273                                                 thermal->chip->chn_id[i]);
1274                 if (error) {
1275                         dev_err(&pdev->dev,
1276                                 "failed to register sensor[%d] : error = %d\n",
1277                                 i, error);
1278                         goto err_disable_pclk;
1279                 }
1280         }
1281
1282         error = devm_request_threaded_irq(&pdev->dev, irq, NULL,
1283                                           &rockchip_thermal_alarm_irq_thread,
1284                                           IRQF_ONESHOT,
1285                                           "rockchip_thermal", thermal);
1286         if (error) {
1287                 dev_err(&pdev->dev,
1288                         "failed to request tsadc irq: %d\n", error);
1289                 goto err_disable_pclk;
1290         }
1291
1292         thermal->chip->control(thermal->regs, true);
1293
1294         for (i = 0; i < thermal->chip->chn_num; i++)
1295                 rockchip_thermal_toggle_sensor(&thermal->sensors[i], true);
1296
1297         platform_set_drvdata(pdev, thermal);
1298
1299         return 0;
1300
1301 err_disable_pclk:
1302         clk_disable_unprepare(thermal->pclk);
1303 err_disable_clk:
1304         clk_disable_unprepare(thermal->clk);
1305
1306         return error;
1307 }
1308
1309 static int rockchip_thermal_remove(struct platform_device *pdev)
1310 {
1311         struct rockchip_thermal_data *thermal = platform_get_drvdata(pdev);
1312         int i;
1313
1314         for (i = 0; i < thermal->chip->chn_num; i++) {
1315                 struct rockchip_thermal_sensor *sensor = &thermal->sensors[i];
1316
1317                 rockchip_thermal_toggle_sensor(sensor, false);
1318         }
1319
1320         thermal->chip->control(thermal->regs, false);
1321
1322         clk_disable_unprepare(thermal->pclk);
1323         clk_disable_unprepare(thermal->clk);
1324
1325         return 0;
1326 }
1327
1328 static int __maybe_unused rockchip_thermal_suspend(struct device *dev)
1329 {
1330         struct platform_device *pdev = to_platform_device(dev);
1331         struct rockchip_thermal_data *thermal = platform_get_drvdata(pdev);
1332         int i;
1333
1334         for (i = 0; i < thermal->chip->chn_num; i++)
1335                 rockchip_thermal_toggle_sensor(&thermal->sensors[i], false);
1336
1337         thermal->chip->control(thermal->regs, false);
1338
1339         clk_disable(thermal->pclk);
1340         clk_disable(thermal->clk);
1341
1342         pinctrl_pm_select_sleep_state(dev);
1343
1344         return 0;
1345 }
1346
1347 static int __maybe_unused rockchip_thermal_resume(struct device *dev)
1348 {
1349         struct platform_device *pdev = to_platform_device(dev);
1350         struct rockchip_thermal_data *thermal = platform_get_drvdata(pdev);
1351         int i;
1352         int error;
1353
1354         error = clk_enable(thermal->clk);
1355         if (error)
1356                 return error;
1357
1358         error = clk_enable(thermal->pclk);
1359         if (error) {
1360                 clk_disable(thermal->clk);
1361                 return error;
1362         }
1363
1364         rockchip_thermal_reset_controller(thermal->reset);
1365
1366         thermal->chip->initialize(thermal->grf, thermal->regs,
1367                                   thermal->tshut_polarity);
1368
1369         for (i = 0; i < thermal->chip->chn_num; i++) {
1370                 int id = thermal->sensors[i].id;
1371
1372                 thermal->chip->set_tshut_mode(id, thermal->regs,
1373                                               thermal->tshut_mode);
1374
1375                 error = thermal->chip->set_tshut_temp(&thermal->chip->table,
1376                                               id, thermal->regs,
1377                                               thermal->tshut_temp);
1378                 if (error)
1379                         dev_err(&pdev->dev, "%s: invalid tshut=%d, error=%d\n",
1380                                 __func__, thermal->tshut_temp, error);
1381         }
1382
1383         thermal->chip->control(thermal->regs, true);
1384
1385         for (i = 0; i < thermal->chip->chn_num; i++)
1386                 rockchip_thermal_toggle_sensor(&thermal->sensors[i], true);
1387
1388         pinctrl_pm_select_default_state(dev);
1389
1390         return 0;
1391 }
1392
1393 static SIMPLE_DEV_PM_OPS(rockchip_thermal_pm_ops,
1394                          rockchip_thermal_suspend, rockchip_thermal_resume);
1395
1396 static struct platform_driver rockchip_thermal_driver = {
1397         .driver = {
1398                 .name = "rockchip-thermal",
1399                 .pm = &rockchip_thermal_pm_ops,
1400                 .of_match_table = of_rockchip_thermal_match,
1401         },
1402         .probe = rockchip_thermal_probe,
1403         .remove = rockchip_thermal_remove,
1404 };
1405
1406 module_platform_driver(rockchip_thermal_driver);
1407
1408 MODULE_DESCRIPTION("ROCKCHIP THERMAL Driver");
1409 MODULE_AUTHOR("Rockchip, Inc.");
1410 MODULE_LICENSE("GPL v2");
1411 MODULE_ALIAS("platform:rockchip-thermal");