drivers/video/fbdev/mmp/hw/mmp_spi.c

   1 /*
   2  * linux/drivers/video/mmp/hw/mmp_spi.c
   3  * using the spi in LCD controler for commands send
   4  *
   5  * Copyright (C) 2012 Marvell Technology Group Ltd.
   6  * Authors:  Guoqing Li <ligq@marvell.com>
   7  *          Lisa Du <cldu@marvell.com>
   8  *          Zhou Zhu <zzhu3@marvell.com>
   9  *
  10  * This program is free software; you can redistribute it and/or modify it
  11  * under the terms of the GNU General Public License as published by the
  12  * Free Software Foundation; either version 2 of the License, or (at your
  13  * option) any later version.
  14  *
  15  * This program is distributed in the hope that it will be useful, but WITHOUT
  16  * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  17  * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  18  * more details.
  19  *
  20  * You should have received a copy of the GNU General Public License along with
  21  * this program.  If not, see <http://www.gnu.org/licenses/>.
  22  *
  23  */
  24 #include <linux/errno.h>
  25 #include <linux/delay.h>
  26 #include <linux/err.h>
  27 #include <linux/io.h>
  28 #include <linux/spi/spi.h>
  29 #include "mmp_ctrl.h"
  30
  31 /**
  32  * spi_write - write command to the SPI port
  33  * @data: can be 8/16/32-bit, MSB justified data to write.
  34  * @len:  data length.
  35  *
  36  * Wait bus transfer complete IRQ.
  37  * The caller is expected to perform the necessary locking.
  38  *
  39  * Returns:
  40  *   %-ETIMEDOUT        timeout occurred
  41  *   0                  success
  42  */
  43 static inline int lcd_spi_write(struct spi_device *spi, u32 data)
  44 {
  45         int timeout = 100000, isr, ret = 0;
  46         u32 tmp;
  47         void *reg_base =
  48                 *(void **)spi_master_get_devdata(spi->master);
  49
  50         /* clear ISR */
  51         writel_relaxed(~SPI_IRQ_MASK, reg_base + SPU_IRQ_ISR);
  52
  53         switch (spi->bits_per_word) {
  54         case 8:
  55                 writel_relaxed((u8)data, reg_base + LCD_SPU_SPI_TXDATA);
  56                 break;
  57         case 16:
  58                 writel_relaxed((u16)data, reg_base + LCD_SPU_SPI_TXDATA);
  59                 break;
  60         case 32:
  61                 writel_relaxed((u32)data, reg_base + LCD_SPU_SPI_TXDATA);
  62                 break;
  63         default:
  64                 dev_err(&spi->dev, "Wrong spi bit length\n");
  65         }
  66
  67         /* SPI start to send command */
  68         tmp = readl_relaxed(reg_base + LCD_SPU_SPI_CTRL);
  69         tmp &= ~CFG_SPI_START_MASK;
  70         tmp |= CFG_SPI_START(1);
  71         writel(tmp, reg_base + LCD_SPU_SPI_CTRL);
  72
  73         isr = readl_relaxed(reg_base + SPU_IRQ_ISR);
  74         while (!(isr & SPI_IRQ_ENA_MASK)) {
  75                 udelay(100);
  76                 isr = readl_relaxed(reg_base + SPU_IRQ_ISR);
  77                 if (!--timeout) {
  78                         ret = -ETIMEDOUT;
  79                         dev_err(&spi->dev, "spi cmd send time out\n");
  80                         break;
  81                 }
  82         }
  83
  84         tmp = readl_relaxed(reg_base + LCD_SPU_SPI_CTRL);
  85         tmp &= ~CFG_SPI_START_MASK;
  86         tmp |= CFG_SPI_START(0);
  87         writel_relaxed(tmp, reg_base + LCD_SPU_SPI_CTRL);
  88
  89         writel_relaxed(~SPI_IRQ_MASK, reg_base + SPU_IRQ_ISR);
  90
  91         return ret;
  92 }
  93
  94 static int lcd_spi_setup(struct spi_device *spi)
  95 {
  96         void *reg_base =
  97                 *(void **)spi_master_get_devdata(spi->master);
  98         u32 tmp;
  99
 100         tmp = CFG_SCLKCNT(16) |
 101                 CFG_TXBITS(spi->bits_per_word) |
 102                 CFG_SPI_SEL(1) | CFG_SPI_ENA(1) |
 103                 CFG_SPI_3W4WB(1);
 104         writel(tmp, reg_base + LCD_SPU_SPI_CTRL);
 105
 106         /*
 107          * After set mode it need a time to pull up the spi singals,
 108          * or it would cause the wrong waveform when send spi command,
 109          * especially on pxa910h
 110          */
 111         tmp = readl_relaxed(reg_base + SPU_IOPAD_CONTROL);
 112         if ((tmp & CFG_IOPADMODE_MASK) != IOPAD_DUMB18SPI)
 113                 writel_relaxed(IOPAD_DUMB18SPI |
 114                         (tmp & ~CFG_IOPADMODE_MASK),
 115                         reg_base + SPU_IOPAD_CONTROL);
 116         udelay(20);
 117         return 0;
 118 }
 119
 120 static int lcd_spi_one_transfer(struct spi_device *spi, struct spi_message *m)
 121 {
 122         struct spi_transfer *t;
 123         int i;
 124
 125         list_for_each_entry(t, &m->transfers, transfer_list) {
 126                 switch (spi->bits_per_word) {
 127                 case 8:
 128                         for (i = 0; i < t->len; i++)
 129                                 lcd_spi_write(spi, ((u8 *)t->tx_buf)[i]);
 130                         break;
 131                 case 16:
 132                         for (i = 0; i < t->len/2; i++)
 133                                 lcd_spi_write(spi, ((u16 *)t->tx_buf)[i]);
 134                         break;
 135                 case 32:
 136                         for (i = 0; i < t->len/4; i++)
 137                                 lcd_spi_write(spi, ((u32 *)t->tx_buf)[i]);
 138                         break;
 139                 default:
 140                         dev_err(&spi->dev, "Wrong spi bit length\n");
 141                 }
 142         }
 143
 144         m->status = 0;
 145         if (m->complete)
 146                 m->complete(m->context);
 147         return 0;
 148 }
 149
 150 int lcd_spi_register(struct mmphw_ctrl *ctrl)
 151 {
 152         struct spi_master *master;
 153         void **p_regbase;
 154         int err;
 155
 156         master = spi_alloc_master(ctrl->dev, sizeof(void *));
 157         if (!master) {
 158                 dev_err(ctrl->dev, "unable to allocate SPI master\n");
 159                 return -ENOMEM;
 160         }
 161         p_regbase = spi_master_get_devdata(master);
 162         *p_regbase = ctrl->reg_base;
 163
 164         /* set bus num to 5 to avoid conflict with other spi hosts */
 165         master->bus_num = 5;
 166         master->num_chipselect = 1;
 167         master->setup = lcd_spi_setup;
 168         master->transfer = lcd_spi_one_transfer;
 169
 170         err = spi_register_master(master);
 171         if (err < 0) {
 172                 dev_err(ctrl->dev, "unable to register SPI master\n");
 173                 spi_master_put(master);
 174                 return err;
 175         }
 176
 177         dev_info(&master->dev, "registered\n");
 178
 179         return 0;
 180 }